Difference between revisions of "Sensor-Temperature-D1"

From Microduino Wiki
Jump to: navigation, search
 
(5 intermediate revisions by 2 users not shown)
Line 11: Line 11:
  
 
==Introduction of the Sensor Pin==
 
==Introduction of the Sensor Pin==
{{Sensor_explain
+
{{ST_Pinout
|nameA=[[Sensor-Temperature-D1]]
+
|st_name=Temperature D1 Sensor
|modeA=SDA
+
|pin3=IIC SDA
|modeB=SCL
+
|pin4=IIC SCL
 
}}
 
}}
 +
 
==Features==
 
==Features==
 
*Adopts LM75 temperature whose address is optional.  
 
*Adopts LM75 temperature whose address is optional.  
Line 37: Line 38:
  
 
*Connection
 
*Connection
*This sensor can e connected to the I2C interface of the core.  
+
**This sensor can e connected to the I2C interface of the core.
  
 
==Document==
 
==Document==
*Schematic diagram: '''[[File: Sensor_Temperature_D1.Zip]]'''
+
*Schematic diagram: '''[[File: Sensor-Temperature-D1.Zip]]'''
 +
*Main chip: '''[[File: LM75 datasheet.pdf]]'''
  
 
==Development==
 
==Development==
 
===Program Download===
 
===Program Download===
*Download and unzip the program '''[[File:Sensor_Temperature_D1_Test.zip]]'''
+
*Download and unzip the program '''[[File:Sensor-Temperature-D1_Test.zip]]'''
  
 
===Programming===
 
===Programming===
Line 55: Line 57:
  
 
===Hardware Setup===
 
===Hardware Setup===
*Referring to the following diagram, connect the Sensor-Temperature-D1 to theI2C interface of '''[[Microduino-Sensorhub]]'''.  
+
*Referring to the following diagram, connect the Sensor-Temperature-D1 to the I2C interface of '''[[Microduino-Sensorhub]]'''.  
 
<br>
 
<br>
 
[[file:Microduino-sensorhub_I2C.JPG|thumb|400px|left]]
 
[[file:Microduino-sensorhub_I2C.JPG|thumb|400px|left]]
Line 75: Line 77:
  
 
*Front
 
*Front
[[file: Microduino-LM75-F.JPG|thumb|600px|center|Microduino-LM75 Front]]
+
[[file: Microduino-LM75-F1.JPG|thumb|600px|center|Microduino-LM75 Front]]
 
*Back
 
*Back
[[file: Microduino-LM75 -b.JPG|thumb|600px|center|Microduino-LM75 Back]]
+
[[file: Microduino-LM75 -b1.JPG|thumb|600px|center|Microduino-LM75 Back]]
 
|}
 
|}

Latest revision as of 06:47, 4 August 2017

Language: English  • 中文
Microduino-Sensor-Temperature-D1

The product number of Sensor-Temperature-D1 is: MSDT11

Sensor-Temperature-D1 is digital temperature detection sensor module.

LM75 is a temperature sensor produced by National Semiconductor whose output voltage is of Celsius scale.

Introduction of the Sensor Pin

Sensor backpin.png

Temperature D1 Sensor
General Pin Out Sensor / Trinket's Pin Out
PIN1 (GND) GND
PIN2 (VCC) VCC
PIN3 (SIGNAL-A) IIC SDA
PIN4 (SIGNAL-B) IIC SCL
  • General Pin Out is the standard pin out of a Sensor / Trinket connector.
  • Sensor / Trinket's Pin Out is this specific Sensor / Trinket's wiring in relation to the General Pin Out.
  • SIGNAL-A / SIGNAL-B are signals that could be digital input, digital output, analog input or analog output. Or special signals such as serial communication (SoftwareSerial, IIC (I2C), etc) or other special signals.
  • Not Connected refers to the Pin not being used for this particular Sensor / Trinket.
  • Read more about the hub module.

Features

  • Adopts LM75 temperature whose address is optional.
  • With high accuracy and sensitivity.
  • With low power consumption, long service life and good stability.
  • With wide working voltage.
  • With small size which is easy to install.

Specification

  • Sensor voltage
    • 3.3V~5V working voltage
  • Size of the sensor
    • Size of the board: 23.5mm*13mm
    • 1.27mm-spacing 4Pin interface connected with sensorhub
    • CAD drawing of the sensor: File:Sensor CAD.zip
  • Technical parameters
    • Accuracy: temperature 0.125℃;
    • Measuring range: 55℃~+125℃;
  • Connection
    • This sensor can e connected to the I2C interface of the core.

Document

Development

Program Download

Programming

  • Follow the Software Getting Started Guide.
  • Select the Board, Processor and Port.
  • Click [File]->[Open], browse to the project program address, and click "Sensor_Temperature_D1_Test.ino" to open the program.
  • After confirming all these items are correct, click "→" to download the program to the development board.

Hardware Setup

  • Referring to the following diagram, connect the Sensor-Temperature-D1 to the I2C interface of Microduino-Sensorhub.


Microduino-sensorhub I2C.JPG


Result

  • After download, open the serial monitor.
  • The serial monitor will print out the configuration information of the sensor, and then display the current temperature in cycle.

Application

It can be used to detect the humidity of the environment, and be sued as temperature switch to control the air conditioner, fan and other devices.


Purchase

History

Gallery

  • Front
File:Microduino-LM75-F1.JPG
Microduino-LM75 Front
  • Back
File:Microduino-LM75 -b1.JPG
Microduino-LM75 Back
Retrieved from "https://wiki.microduinoinc.com/index.php?title=Sensor-Temperature-D1&oldid=21498"