Difference between revisions of "Mixly Block Category - SerialPort"

From Microduino Wiki
Jump to: navigation, search
(parseInt)
(Serial Availability)
 
Line 35: Line 35:
  
 
Read more here: https://www.arduino.cc/en/Serial/Available
 
Read more here: https://www.arduino.cc/en/Serial/Available
 +
 
=Serial Read String=
 
=Serial Read String=
 
Reads characters from the serial buffer into a string. The function terminates if it times out.
 
Reads characters from the serial buffer into a string. The function terminates if it times out.

Latest revision as of 00:49, 1 March 2017

Serial is used for communication between the Microduino / Arduino board and a computer or other devices. All Microduino / Arduino boards have at least one serial port (also known as a UART or USART): Serial. It communicates on digital pins 0 (RX) and 1 (TX) as well as with the computer via USB. Thus, if you use these functions, you cannot also use pins 0 and 1 for digital input or output.


Read more here: https://www.arduino.cc/en/Reference/Serial

Serial Baud Rate

Sets the data rate in bits per second (baud) for serial data transmission. For communicating with the computer, use one of these rates: 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, or 115200.


Read more here: https://www.arduino.cc/en/serial/begin

Serial Write

Writes binary data to the serial port. This data is sent as a byte or series of bytes; to send the characters representing the digits of a number use the print() function instead.


Read more here: https://www.arduino.cc/en/Serial/Write

Serial Print

Prints data to the serial port as human-readable ASCII text. This command can take many forms. Numbers are printed using an ASCII character for each digit. Floats are similarly printed as ASCII digits, defaulting to two decimal places. Bytes are sent as a single character.


Read more here: https://www.arduino.cc/en/Serial/Print

Serial PrintLn

Prints data to the serial port as human-readable ASCII text followed by a carriage return character (ASCII 13, or '\r') and a newline character (ASCII 10, or '\n'). This command takes the same forms as print.


Read more here: https://www.arduino.cc/en/Serial/Println

Serial PrintLn(Hex)

Prints a number to the serial port as human-readable hex format number. Followed by a carriage return character (ASCII 13, or '\r') and a newline character (ASCII 10, or '\n').

Serial Availability

Get the number of bytes (characters) available for reading from the serial port. This is data that's already arrived and stored in the serial receive buffer (which holds 64 bytes). available() inherits from the Stream utility class.


Read more here: https://www.arduino.cc/en/Serial/Available

Serial Read String

Reads characters from the serial buffer into a string. The function terminates if it times out.


Read more here: https://www.arduino.cc/en/Serial/ReadString

Serial Read String Until Character Delimitation

Reads characters from the serial buffer into a string. The function terminates if the terminator character is detected or it times out.


Read more here: https://www.arduino.cc/en/Serial/ReadStringUntil

Serial Read

read

Reads incoming serial data.


Read more here: https://www.arduino.cc/en/Serial/Read

peek

Returns the next byte (character) of incoming serial data without removing it from the internal serial buffer. That is, successive calls to peek will return the same character, as will the next call to read.


Read more here: https://www.arduino.cc/en/Serial/Peek

parseInt

Looks for the next valid integer in the incoming serial stream.


Read more here: https://www.arduino.cc/en/Serial/ParseInt

parseFloat

parseFloat returns the first valid floating point number from the Serial buffer. Characters that are not digits (or the minus sign) are skipped. parseFloat is terminated by the first character that is not a floating point number.


Read more here: https://www.arduino.cc/en/Serial/ParseFloat

Serial Flush

Waits for the transmission of outgoing serial data to complete.


Read more here: https://www.arduino.cc/en/Serial/Flush

Software Serial Setup

Initializes the pins for SoftwareSerial. Starting SoftwareSerial is done with the begin function block.