Revision as of 23:53, 29 October 2018 (view source) Sonny (talk | contribs) (→‎Motor - Set Speed) ← Older edit		Revision as of 18:47, 1 November 2018 (view source) Sonny (talk | contribs) (→‎Car - Color Trace) Newer edit →
Line 72:		Line 72:
	=Car - Color Trace=		=Car - Color Trace=
−	This block control the Buggy Base to follow (trace) along the chosen color line.	+	This block controls the Buggy Base to follow (trace) along the chosen color line.
	:[[File:IBB mDesigner Car Block Go Along Color.png]]		:[[File:IBB mDesigner Car Block Go Along Color.png]]

---

Revision as of 18:47, 1 November 2018

The Buggy Base found in the Itty Bitty Buggy kit is a unique piece of hardware. It contains the following:

• Motor driver
• 2 Motors
• 2 Color Detectors
• 2 Color LEDs
• Buzzer

The above components are not controlled directly (i.e. via pins). Rather there is an embedded micro-controller which controls those components. The embedded micro-controller can be communicated via serial communication.

Buggy Base was developed to be a line-detecting vehicle base, but can be re-purposed for other uses such as a walking robot or climbing robot (as shown in the Itty Bitty Buggy projects).

Compatible Pins

The Buggy Base is controllable over serial communication. When using mDesigner, the serial pins used are Serial1, which are pins 2/3 on a mCenter+ (Core+) module.

Car - Move

Note: This block is holding. Which means the movement time (as set by Duration) must complete before the program goes to the next block in the script.

This blocks controls the Buggy Base to move either forward or backwards at a certain speed for a specified duration.

• Direction - direction to move. Either forward or backward.

• Speed - rate of the motors when moving. A value between 0 and 255. 0 being off, 255 being full speed, and 127 being half speed.

• Duration - amount of time (in seconds) to move.

Car - Turn

Note: This block is holding. Which means the movement time (as set by Duration) must complete before the program goes to the next block in the script.

This blocks controls the Buggy Base to turn either right or left at a certain speed for a specified duration.

• Turn Direction - direction to turn. Either left or right.

• Speed - rate of the motors when turning. A value between 0 and 255. 0 being off, 255 being full speed, and 127 being half speed.

Motor - Set Speed

Note: This block is NOT holding. Which means once the motor's speed is set, then the program will go to the next block immediately. The motor will continue to run.

This block sets the speed of the selected motor.

• Motor - select motor (either A, B, or AB (both)).

• Speed - rate to set the selected Motor. A value between -255 and 255. Negative values will spin the motor in reverse.

• 0 being off
• 127 being half speed forward.
• 255 being full speed forward
• -255 being full speed backward
• -127 being half speed backward

Motor - Stop

This block stops the selected motor.

• Motor - select motor to stop (either A, B, or AB (both)).

ColorLED - Set Color

This block sets the selected ColorLED to the chosen color.

• ColorLED - select ColorLED to set color for (either A or B).

• Color - color to set selected ColorLED to.

Car - Color Trace

This block controls the Buggy Base to follow (trace) along the chosen color line.

• Color - color of the line to trace (either red, green, blue or black).

Car - Stop Trace

This block stops the Buggy Base following the line (tracing).

Color Detector - Detect Color

Note: This block approximates the color detected. Therefore, closely related colors may be register as being detected. An example, "orange" registers as "red".

This block reads and returns either true or false if the selected color detector detects the selected test color.

• Sensor - select sensor for detection (either A or B).

• Color - color for the selected Sensor to match in order to return true. Otherwise, this block returns false.

Buzzer - Play Note

This block controls the Buzzer to play the selected note for the specified duration.

Note: If the duration (seconds) is set (not 0) this block is holding. Which means the note must complete playing before the program goes to the next block in the script.

Note: As of mDesigner v1.6: In "online mode" this block accepts whole and decimal numbers. In "offline mode" this block only accepts WHOLE numbers. Decimal numbers will be rounded down.

• Note - select note to play.

• Duration - time in seconds to play the selected note.

Buzzer - Play Song

This block controls the Buzzer to play the selected song.

Note: This block is holding. Which means the song must complete playing before the program goes to the next block in the script.

Note: As of mDesigner v1.6: In "offline mode" this block doesn't work correctly.

• Song - selected song to play.

Buzzer - Off

Note: As of mDesigner v1.6, this block has no intended purpose because the Buzzer - Play Note and Buzzer - Play Song blocks will stop automatically based on the duration.

This block controls the Buzzer to stop producing sound.

Color Detector - Read Color

This block reads and returns the raw value from the color detector while having the corresponding ColorLED set to a specific color.

• Sensor - sensor to read raw value from (either A or B).

• Color - turn on the corresponding ColorLED to the selected color (either red, green, blue or OFF).

Note: Turning on the corresponding paired ColorLED can help improve the consistency of the raw data readings. ColorLED "A" and Color Detector "A" are on the same side. Similarly with ColorLED "B" and Color Detector "B".