Difference between revisions of "Mixly Block Category - Communicate"
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Infrared= | =Infrared= | ||
| + | The Arduino IRremote library lets you control your Arduino through a standard infrared remote control, or use your Arduino to control other devices (TV, stereo, etc). | ||
| + | |||
| + | Read more here: https://github.com/z3t0/Arduino-IRremote/wiki | ||
| + | ==Enable IR In== | ||
==IR Receive== | ==IR Receive== | ||
==IR Send== | ==IR Send== | ||
| − | |||
==IR Receive (RAW)== | ==IR Receive (RAW)== | ||
=I2C= | =I2C= | ||
| + | These blocks allows you to communicate with I2C / TWI devices. | ||
| + | |||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/Wire | ||
==I2C (Master) Write== | ==I2C (Master) Write== | ||
| + | A Master device runs this block which writes data to a Slave device. | ||
| + | *Slave device address - address of the slave address that data will be written to. | ||
| + | *Value - Byte that is written to the slave device. | ||
| + | |||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/WireWrite | ||
==I2C (Master) Read== | ==I2C (Master) Read== | ||
| + | A Master device runs this block which reads data from a Slave device. | ||
| + | *Slave device address - address of the slave address that data will be read from. | ||
| + | *Number of bytes - Amount of bytes to read from the slave device. | ||
| + | |||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/WireRead | ||
==I2C (Slave) Read== | ==I2C (Slave) Read== | ||
| − | ==I2C (Master) Data Availability from Slave= | + | A Slave device runs this block which reads data from the Master device. |
| + | |||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/WireRead | ||
| + | ==I2C (Master) Data Availability from Slave== | ||
| + | A slave device | ||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/WireAvailable | ||
=SPI= | =SPI= | ||
| + | This library allows you to communicate with SPI devices, with the Arduino as the master device. | ||
| + | |||
| + | Read more here: https://www.arduino.cc/en/reference/SPI | ||
==Send Data to Slave== | ==Send Data to Slave== | ||
| + | |||
| + | |||
| + | Read more here: https://www.arduino.cc/en/Reference/SPITransfer | ||
Latest revision as of 01:50, 22 February 2017
Contents
Infrared
The Arduino IRremote library lets you control your Arduino through a standard infrared remote control, or use your Arduino to control other devices (TV, stereo, etc).
Read more here: https://github.com/z3t0/Arduino-IRremote/wiki
Enable IR In
IR Receive
IR Send
IR Receive (RAW)
I2C
These blocks allows you to communicate with I2C / TWI devices.
Read more here: https://www.arduino.cc/en/Reference/Wire
I2C (Master) Write
A Master device runs this block which writes data to a Slave device.
- Slave device address - address of the slave address that data will be written to.
- Value - Byte that is written to the slave device.
Read more here: https://www.arduino.cc/en/Reference/WireWrite
I2C (Master) Read
A Master device runs this block which reads data from a Slave device.
- Slave device address - address of the slave address that data will be read from.
- Number of bytes - Amount of bytes to read from the slave device.
Read more here: https://www.arduino.cc/en/Reference/WireRead
I2C (Slave) Read
A Slave device runs this block which reads data from the Master device.
Read more here: https://www.arduino.cc/en/Reference/WireRead
I2C (Master) Data Availability from Slave
A slave device
Read more here: https://www.arduino.cc/en/Reference/WireAvailable
SPI
This library allows you to communicate with SPI devices, with the Arduino as the master device.
Read more here: https://www.arduino.cc/en/reference/SPI
Send Data to Slave
Read more here: https://www.arduino.cc/en/Reference/SPITransfer
