Difference between revisions of "Mixly Block Category - Sensor"
(Created page with "=Read Ultrasonic Range= =Get Temperature/Humidity from DHT11= =Get Temperature from DS18B20= =Initialize GPS= =Read and Print GPS Data=") |
(→Read and Print GPS Data) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | =Read | + | =Ultrasonic Sensor= |
| − | =Get Temperature | + | An Ultrasonic Sensor uses ultrasonic sound to detect the range of an object in which the sound wave is directed towards. |
| − | =Get Temperature | + | |
| − | =Initialize GPS= | + | |
| − | =Read and Print GPS Data= | + | Read more here: http://randomnerdtutorials.com/complete-guide-for-ultrasonic-sensor-hc-sr04/ |
| + | ==Read Range (cm)== | ||
| + | This block returns the distance in centimeters (cm) that the Ultrasonic Sensor detects a object to be. | ||
| + | *Trigger Pin - Is the pin used to activate the ultrasonic ping on the sensor. | ||
| + | *Echo Pin - Is the pin which detects / returns the result of the ultrasonic ping. Basically, the distance detected. | ||
| + | |||
| + | =DHT11= | ||
| + | The DHT11 is a sensor used to measure temperature and humidity. | ||
| + | |||
| + | |||
| + | Read more here: http://playground.arduino.cc/Main/DHTLib | ||
| + | ==Get Temperature== | ||
| + | Returns the temperature (in ?) detected by the DHT11 sensor. | ||
| + | *Pin # - The pin number that the DHT11 is attached to. | ||
| + | |||
| + | ==Get Humidity== | ||
| + | Returns the humidity (in ?) detected by the DHT11 sensor. | ||
| + | *Pin # - The pin number that the DHT11 is attached to. | ||
| + | |||
| + | =DS18B20= | ||
| + | The DS18B20 is a sensored used to measure temperature. | ||
| + | ==Get Temperature== | ||
| + | Returns the temperature in Celsius or Fahrenheit detected by the DS18B20 sensor. | ||
| + | *Pin # - The pin number that the DS18B20 is attached to. | ||
| + | *Temperature Return Type - Select to return temperature in either Celsius or Fahrenheit. | ||
| + | |||
| + | =GPS= | ||
| + | GPS is used measure location. | ||
| + | |||
| + | |||
| + | Read more here: http://playground.arduino.cc/Tutorials/GPS | ||
| + | ==Initialize== | ||
| + | This block initializes the GPS software and defines the pins that the GPS is connected to. Communication is done with serial communication. | ||
| + | *RX Pin - The pin that the Core modules will receive data from the GPS module. | ||
| + | *TX Pin - The pin that the Core modules will send data to the GPS module. | ||
| + | *Baud Rate - The speed in which data (bits per seconds) is communicated upon. | ||
| + | ==Read and Print GPS Data== | ||
| + | This block loops continuously and reads data from the GPS module. | ||
Latest revision as of 21:51, 23 February 2017
Contents
Ultrasonic Sensor
An Ultrasonic Sensor uses ultrasonic sound to detect the range of an object in which the sound wave is directed towards.
Read more here: http://randomnerdtutorials.com/complete-guide-for-ultrasonic-sensor-hc-sr04/
Read Range (cm)
This block returns the distance in centimeters (cm) that the Ultrasonic Sensor detects a object to be.
- Trigger Pin - Is the pin used to activate the ultrasonic ping on the sensor.
- Echo Pin - Is the pin which detects / returns the result of the ultrasonic ping. Basically, the distance detected.
DHT11
The DHT11 is a sensor used to measure temperature and humidity.
Read more here: http://playground.arduino.cc/Main/DHTLib
Get Temperature
Returns the temperature (in ?) detected by the DHT11 sensor.
- Pin # - The pin number that the DHT11 is attached to.
Get Humidity
Returns the humidity (in ?) detected by the DHT11 sensor.
- Pin # - The pin number that the DHT11 is attached to.
DS18B20
The DS18B20 is a sensored used to measure temperature.
Get Temperature
Returns the temperature in Celsius or Fahrenheit detected by the DS18B20 sensor.
- Pin # - The pin number that the DS18B20 is attached to.
- Temperature Return Type - Select to return temperature in either Celsius or Fahrenheit.
GPS
GPS is used measure location.
Read more here: http://playground.arduino.cc/Tutorials/GPS
Initialize
This block initializes the GPS software and defines the pins that the GPS is connected to. Communication is done with serial communication.
- RX Pin - The pin that the Core modules will receive data from the GPS module.
- TX Pin - The pin that the Core modules will send data to the GPS module.
- Baud Rate - The speed in which data (bits per seconds) is communicated upon.
Read and Print GPS Data
This block loops continuously and reads data from the GPS module.
