Difference between revisions of "Sensor / Trinket Template"
From Microduino Wiki
(Created page with "thumb|right =Introduction= The Microduino Crash Sensor is module which can detect if it is pressed or not. It acts a button or switch. =Te...") |
(→Arduino IDE) |
||
| (33 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
*'''Schematics:''' [[File:na]] | *'''Schematics:''' [[File:na]] | ||
*'''Dimensions:''' | *'''Dimensions:''' | ||
| + | |||
| + | =Compatible Pins= | ||
| + | Use a connector wire to connect this module to either a [[Microduino Hub module]], [[mCookie Hub module]], [[mCenter+]], or any other boards which accepts the standard 4-pin connector for a sensor / trinket. | ||
| + | |||
| + | This module requires a '''digital input''' compatible pin as shown below: | ||
| + | |||
| + | [[image of compatible pins]] | ||
| + | |||
| + | =Hardware Setup= | ||
| + | The bare minimum hardware configurations to used this module is as follows: | ||
| + | ==Microduino Series== | ||
| + | <tab name="View" style="width: 100%" collapsed> | ||
| + | [[File:Microduino_Crash-rect.jpg|thumb|right]] | ||
| + | *1x of the following core modules: Microduino Core, Microduino Core+, Microduino CoreUSB, or Microduino CoreRF | ||
| + | *1x Microduino USBTTL | ||
| + | *1x Microduino Connector Hub | ||
| + | *1x Connector Wire | ||
| + | *'''1x Crash Sensor''' | ||
| + | </tab> | ||
| + | |||
| + | ==mCookie Series== | ||
| + | <tab name="View" style="width:100%" collapsed> | ||
| + | [[File:Microduino_Crash-rect.jpg|thumb|right]] | ||
| + | *1x of the following core modules: mCookie Core, mCookie Core+, mCookie CoreUSB, or mCookie CoreRF | ||
| + | *1x of the following core programmers: mCookie USB-TTL, or mCookie mBattery (built-in programmer) | ||
| + | *1x mCookie Connector Hub | ||
| + | *1x Connector Wire | ||
| + | *'''1x Crash Sensor''' | ||
| + | </tab> | ||
| + | |||
| + | ==mCookie Series (using mCenter+)== | ||
| + | <tab name="View" style="width:100%" collapsed> | ||
| + | [[File:Microduino_Crash-rect.jpg|thumb|right]] | ||
| + | *1x mCenter+ (built-in mCookie Core+ & programmer) | ||
| + | *1x Connector Wire | ||
| + | *'''1x Crash Sensor''' | ||
| + | </tab> | ||
| + | |||
| + | =Usage= | ||
| + | ==Arduino IDE== | ||
| + | ===Digital Read=== | ||
| + | <syntaxhighlight lang="cpp"> | ||
| + | digitalRead(pinNum) | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | {| | ||
| + | |'''Description:''' | ||
| + | |Reads the current value of the Crash Sensor. | ||
| + | |- | ||
| + | |'''Arguments:''' | ||
| + | |pinNum - the pin number that the Crash Sensor is connected to. | ||
| + | |- | ||
| + | |'''Return:''' | ||
| + | |'''true''' or '''high''' when the Crash Sensor is NOT pressed. | ||
| + | |- | ||
| + | | | ||
| + | |'''false''' or '''low''' when the Crash Sensor is pressed. | ||
| + | |} | ||
Latest revision as of 20:37, 22 February 2019
Contents
Introduction
The Microduino Crash Sensor is module which can detect if it is pressed or not. It acts a button or switch.
Technical Specifications
- SKU / module number: MSDS11
- Operating voltage: 5V
- Connectors: n/a
- Chip Used: n/a
- Schematics: File:Na
- Dimensions:
Compatible Pins
Use a connector wire to connect this module to either a Microduino Hub module, mCookie Hub module, mCenter+, or any other boards which accepts the standard 4-pin connector for a sensor / trinket.
This module requires a digital input compatible pin as shown below:
Hardware Setup
The bare minimum hardware configurations to used this module is as follows:
Microduino Series
mCookie Series
mCookie Series (using mCenter+)
Usage
Arduino IDE
Digital Read
digitalRead(pinNum)| Description: | Reads the current value of the Crash Sensor. |
| Arguments: | pinNum - the pin number that the Crash Sensor is connected to. |
| Return: | true or high when the Crash Sensor is NOT pressed. |
| false or low when the Crash Sensor is pressed. |
