Difference between revisions of "Microduino-Shield Cube-S1"

From Microduino Wiki
Jump to: navigation, search
(→‎Features)
 
(10 intermediate revisions by 2 users not shown)
Line 6: Line 6:
 
==Features==
 
==Features==
 
*Compatible with the pin of Arduino Uno;
 
*Compatible with the pin of Arduino Uno;
−
*Uniformed Microduino interface standard and rich peripheral modules, capable of having a fast and flexible connection and extension with other modules and sensors meeting Microduino interface standard;
+
*Uniform Microduino interface standard and rich peripheral modules, capable of having a fast and flexible connection and extension with other modules and sensors meeting Microduino interface standard;
 
*Onboard analog button and sensor interface;
 
*Onboard analog button and sensor interface;
  
 
==Specification==
 
==Specification==
−
*Electrical specifications
+
*Electrical specification
−
**MicroUSB power supply；
+
**MicroUSB power supply;
−
**3.3V regular；
+
**3.3V constant voltage;
−
**Select the 5V or 3.3V power via PWR jumper, default is 3.3V；
+
**Select the 5V or 3.3V power via PWR jumper(The default voltage is 3.3V);
−
**Onboard power supply (5V、PWR) indicator；
+
**Onboard power supply indicator(5V and PWR).
  
−
*Extended pin
+
*Extension
−
**Onboard reset button；
+
**Onboard reset button;
−
**OLED fixed base；
+
**The fixed OLED base;
−
**Two serial ports, RX0、TX0(Serial) and D2、D3(Serial1)；
+
**Two serial ports including (RX0, TX0)and (D2, D3);
−
**Two IIC interfaces；
+
**Two IIC interfaces;
−
***Two analogy button interfaces, and connect to A7；
+
***Two analog button interfaces connected to A7;
−
**Sensor interface can be combined by jumper, The player can make the connection by yoursefl, as follows：
+
**The sensor interface can be selected and combined through jumpers:
−
***PWR, A3, GND, PWR or PWR, A3, GND, GND or PWR, D6, GND, PWR or PWR, D6, GND,GND.
+
***PWR, A3, GND, PWR or PWR, A3, GND, GND or PWR, D6, GND, PWR or PWR, D6, GND,GND (Users can make the connection as they like).
  
 
[[file:Microduino-Cube-S1-Pinout1.jpg|800px|thumb|center|Microduino-Cube-S1]]
 
[[file:Microduino-Cube-S1-Pinout1.jpg|800px|thumb|center|Microduino-Cube-S1]]
Line 30: Line 30:
  
 
==Document==
 
==Document==
−
Eagle PCB local downlaod
+
Eagle PCB: '''[[File:Microduino-Cube-S1.zip]]'''
−
Main components：
+
 
−
*3.3V Regulator chip LP2985： '''[[File:LP2985.pdf]]'''
+
Main Component:
 +
*3.3V Voltage Stabilizing chip LP2985： '''[[File:LP2985.pdf]]'''
  
 
==Development==
 
==Development==
  
−
It can be used with other Microduino modules, sensor to achieve specific functions.
+
Microduino-Cube-S1 is capable of having a fast and flexible connection and extension with other modules and sensors meeting Microduino interface standard, achieving specific function.
  
 
[[file:Microduino-Cube-S1-Pinout4.jpg|800px|thumb|center|Microduino-Cube-S1]]
 
[[file:Microduino-Cube-S1-Pinout4.jpg|800px|thumb|center|Microduino-Cube-S1]]
  
 
==Application==
 
==Application==
−
*You can download the test example, and combine OLED to test two analogy of Microduino-Cube-S1, test program：
+
*You can download Microduino test program, which together with OLED to test the function of Microduino-Cube-S1's two analog buttons. Just as follows:
 
https://github.com/Microduino/Microduino_Tutorials/commit/b0e0fe74269ee0f6a886d8fa8db497ec57cc4073
 
https://github.com/Microduino/Microduino_Tutorials/commit/b0e0fe74269ee0f6a886d8fa8db497ec57cc4073
−
*Prepared hardware：Microduino FT232R, Microduino Core, Microduino-Cube-S1, Microduino OLED；
+
*Hardware Needed：Microduino FT232R, Microduino Core, Microduino-Cube-S1 and Microduino OLED;
−
*Prepared software：Microduino example program (Arduino part), Arduino IDE(1.0 release and upper)；
+
*Software Needed：Microduino example program (Arduino part) and Arduino IDE(Version 1.0 and higher);
−
*Open the example program in IDE, select the board "Microduino Core (Atmega328P@16M,5V)", download directly;
+
*Open the example program in IDE, select the board "Microduino Core (Atmega328P@16M,5V)", then download directly;
−
*After download, OLED displays "No button is pressed ",
+
*After the download, "No button is pressed " is displayed on the OLED,
−
**Press the left button, OLED displays "Press the left button" which means the left button was pressed；
+
**Press the left button and "Press the left button" will come out, meaning the left button gets pressed;
−
**Press the right button, OLED displays "Press the rignt button" which means the right button was pressed；
+
**Press the right button and "Press the right button" will be displayed on the OLED, meaning the right button is pressed;
−
**If no button was pressed, OLED displays "No button is pressed ", the same state with initial state.
+
**When no button is pressed, "No button is pressed " will be displayed, which is just like the initial state.
  
 
==Bug==
 
==Bug==

Latest revision as of 06:24, 4 August 2017

Language: English  • 中文
Microduino-Cube-S1

Features

  • Compatible with the pin of Arduino Uno;
  • Uniform Microduino interface standard and rich peripheral modules, capable of having a fast and flexible connection and extension with other modules and sensors meeting Microduino interface standard;
  • Onboard analog button and sensor interface;

Specification

  • Electrical specification
    • MicroUSB power supply;
    • 3.3V constant voltage;
    • Select the 5V or 3.3V power via PWR jumper(The default voltage is 3.3V);
    • Onboard power supply indicator(5V and PWR).
  • Extension
    • Onboard reset button;
    • The fixed OLED base;
    • Two serial ports including (RX0, TX0)and (D2, D3);
    • Two IIC interfaces;
      • Two analog button interfaces connected to A7;
    • The sensor interface can be selected and combined through jumpers:
      • PWR, A3, GND, PWR or PWR, A3, GND, GND or PWR, D6, GND, PWR or PWR, D6, GND,GND (Users can make the connection as they like).
Microduino-Cube-S1
Microduino-Cube-S1-Pinout
Microduino-Cube-S1-Pinout

Document

Eagle PCB: File:Microduino-Cube-S1.zip

Main Component:

Development

Microduino-Cube-S1 is capable of having a fast and flexible connection and extension with other modules and sensors meeting Microduino interface standard, achieving specific function.

Microduino-Cube-S1

Application

  • You can download Microduino test program, which together with OLED to test the function of Microduino-Cube-S1's two analog buttons. Just as follows:

https://github.com/Microduino/Microduino_Tutorials/commit/b0e0fe74269ee0f6a886d8fa8db497ec57cc4073

  • Hardware Needed：Microduino FT232R, Microduino Core, Microduino-Cube-S1 and Microduino OLED;
  • Software Needed：Microduino example program (Arduino part) and Arduino IDE(Version 1.0 and higher);
  • Open the example program in IDE, select the board "Microduino Core (Atmega328P@16M,5V)", then download directly;
  • After the download, "No button is pressed " is displayed on the OLED,
    • Press the left button and "Press the left button" will come out, meaning the left button gets pressed;
    • Press the right button and "Press the right button" will be displayed on the OLED, meaning the right button is pressed;
    • When no button is pressed, "No button is pressed " will be displayed, which is just like the initial state.

Bug

History

Picture

Front

Microduino-Cube-S1 Front

Back

Microduino-Cube-S1 Back

Video

Retrieved from "https://wiki.microduinoinc.com/index.php?title=Microduino-Shield_Cube-S1&oldid=21494"