Difference between revisions of "Microduino-LM4863"
From Microduino Wiki
| (3 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Language|Microduino-LM4863}} | ||
{| style="width: 800px;" | {| style="width: 800px;" | ||
|- | |- | ||
| | | | ||
[[file:Microduino-LM4863-rect1.jpg|400px|thumb|right|Microduino-LM4863]] | [[file:Microduino-LM4863-rect1.jpg|400px|thumb|right|Microduino-LM4863]] | ||
| + | Microduino-LM4863 is a D-Class Amplifier Module. Widely used in music embedded system. | ||
| + | |||
|- | |- | ||
| | | | ||
| + | ==Feature== | ||
| + | *2.54 Connector with good compatibility; | ||
| + | *Suppress power noise, gain stability; | ||
| + | *Small, cheap, stackable, opened platform | ||
| + | *Open source hardware circuit design, compatible with the Arduino IDE development environment for programming; | ||
| + | *Define unified interface Microduino specification and contain rich peripheral modules. Set up the quick connection with other Microduino modules and sensors easily and flexibly; | ||
| + | *2.54 pitch row female connector for easy integration into breadboard. | ||
| + | |||
| + | |- | ||
| + | | | ||
==Specifications== | ==Specifications== | ||
| + | *Provide 2.2W output for 4Ω load; | ||
| + | *Operating Voltage：2.0-5.5V； | ||
| + | *Externally controlled, low-power shutdown mode, typical shutdown current of 0.7uA. | ||
| + | |||
[[File:LM4863-Pinout-2.jpg|800px|thumb|center|Microduino-LM4863-Pinout]] | [[File:LM4863-Pinout-2.jpg|800px|thumb|center|Microduino-LM4863-Pinout]] | ||
[[File:LM4863-Pinout-1.jpg|800px|thumb|center|Microduino-LM4863-Pinout]] | [[File:LM4863-Pinout-1.jpg|800px|thumb|center|Microduino-LM4863-Pinout]] | ||
| + | |||
| + | ==Document== | ||
| + | Eagle PCB '''[[File:Microduino-LM4863.zip]]''' | ||
| + | |||
| + | ===Main Component=== | ||
| + | *Amplifier chip：LM4863 '''[[File:LM4863.pdf]]''' | ||
| + | |||
| + | ==Development== | ||
| + | *Make sure the 5V power supply current can reach 500ma, not recommended use FT232R debugging directly, becasue FT232R's output current is small. | ||
| + | |||
| + | ===Arduino library and supported package=== | ||
| + | *【SimpleSDAudio library'''[[http://www.hackerspace-ffm.de/wiki/index.php?title=SimpleSDAudio download ]''' 】 | ||
| + | *【SimpleSDAudio updated library '''[[File:Lib SimpleSDAudio.zip]]''' 】 | ||
| + | |||
| + | |||
| + | ===How to use the library=== | ||
| + | *Original library SD module CS pin is D4, need change to D7; | ||
| + | *Original library can not directly support Microduino Core +, we have modified this library to solve this problem; | ||
| + | |||
| + | *Recommend 2GB or less (including 2GB) FAT format TF card. | ||
| + | |||
| + | |||
| + | ===Externally controlled low-power shutdown=== | ||
| + | *In many applications, the shutdown port's level conversion is finished by the controller, but it can also be used to implement by a one-way blade switch; | ||
| + | **Connect a pull-up resistor on the third pin of Second row pin female which near the D13 pin, then disconnect switch, this pin will be pulled low, so the Amplifier begin to work; | ||
| + | **Turn on the switch，pull-up resistor will pull up the voltage, then LM4863 stop work. | ||
| + | |||
| + | ==Application== | ||
| + | |||
| + | ===Program Download=== | ||
| + | *Audio file conversion tool：'''[[File:Tools_lm4863.zip]]''' | ||
| + | |||
| + | ===The Audio experiment using Core and SD=== | ||
| + | *Prepared Hardware：Microduino FT232R、Microduino Core、Microduino SD、Microduino LM4863； | ||
| + | *Prepared Software：Arduino IDE（1.0 release upper）、Microduino provides test program（Arduino part）、SimpleSDAudio library、Audio file creation tools； | ||
| + | *Put the downloaded library to the libraries folder of Arduino IDE installation; | ||
| + | *Copy the "EXAMPLE.AFAM" in examples folder to memory card; | ||
| + | *Start Arduino IDE，open the "BareMinimum" program,card type chosse "Microduino Core (Atmega328P@16M,5V)",download directly； | ||
| + | *Then you can listen it！ | ||
| + | **If you want to play your own audio, just need replace the "EXAMPLE.AFM" by you made audio file. | ||
| + | |||
| + | ===The process to make an audio file=== | ||
| + | *Convert any audio file into a. Wav format using a software "Format Factory"; | ||
| + | *Generate an audio file： | ||
| + | **We need to use a SoX-based tool, and then choose the appropriate conversion process based on the operating frequency that your Microduino selected; | ||
| + | **Decompression the tool，then enter into“Arduino with 16 MHz”folder，put the audio file into this folder,and drag to "FullRate@16MHz_Stereo.bat" (16M full stereo) batch on； | ||
| + | **then you can convert the file, will pop up a dialog box appears "Press any key to continue ..."; | ||
| + | **After completed, you will find a new folder, the converted file is there. | ||
==Pictures== | ==Pictures== | ||
Latest revision as of 01:41, 16 February 2014
| Language: | English • 中文 |
|---|
|
Microduino-LM4863 is a D-Class Amplifier Module. Widely used in music embedded system. |
Feature
|
Specifications
DocumentEagle PCB File:Microduino-LM4863.zip Main Component
Development
Arduino library and supported package
How to use the library
Externally controlled low-power shutdown
ApplicationProgram Download
The Audio experiment using Core and SD
The process to make an audio file
Pictures
|
