MCookie Upin27 Layout

Each stack-able mCookie module uses a set of 27 pins.

Below is the chart which shows which pins are used for each specific module and can be used to find overlaps. If a conflict or overlap exist it is unlikely that both modules will be usable at the same time for a project. See section Known Conflicts to see a list of already known conflicts.

Examples

Example 1

• A mCookie Core module is picked as a Core module. mCookie Core provides the pins for functionality.
• A mCookie Motor is stacked. mCookie Motor uses pins D5, D6, D7, and D8 from the mCookie Core module. D5, D6, D7, D8 are now used / consumed / occupied by the mCookie Motor module.
• No conflicts exists.

Example 2

• A mCookie Core module is picked as a Core module. mCookie Core provides the pins for functionality.
• A mCookie Motor is stacked. mCookie Motor uses pins D5, D6, D7, and D8 from the mCookie Core module. D5, D6, D7, D8 are now used / consumed / occupied by the mCookie Motor module.
• A mCookie AudioPro is stack. mCookie AudioPro uses pins D13, D12, D11, D8.
• Pin D8 is now conflicted. D8 on mCookie Motor is used for motor control. D8 on mCookie SD is used to select the SD card module in SPI mode. Therefore, both modules will not work correctly because of the overlapping pin.

Upin27 Layout

• Each stack-able mCookie module uses a set of 27 pins.
• Core modules provides pins to other modules.
  • Only one Core module type should exist in a build / project.
  • Usage of a stack splitter such as mBattery or DUO simply allow the stack to be shorter by splitting the stack height, but both stacks are still connected.
• Core Programmers are needed to upload a program to a Core module (except for CoreUSB, as there is an integrated programmer).
  • Core programmers use RX_ [D0] & TX_ [D1] on a Core module for programming.
  • RX_ [D0] & TX_ [D1] are also used for Serial communication with the Serial Monitor from the Core module to the Computer.
  • Programming and Serial Monitor does not cause a conflict.
  • RX_ [D0] & TX [D1] are also typically used by Communication modules such as Bluetooth and WiFi. Please be aware of this possible conflict.
  • Re-wiring on the Communication module may be needed in order to use a different pin set.
• Other modules (non-Core modules) uses pins provided by Core modules.
• Pin names for a non-Core module are sometimes repeated.
  • The default configuration is in not parenthesis, while a re-wiring alternative is in parenthesis.
  • Some modules need to be re-wired in order to avoid pin conflicts. See individual pages for re-wiring information.
• Power is provided by power giving modules such as mBattery, Battery Management, etc. The power pins 5V, 3V3 and GND are share-able across all modules and do not cause a conflict.
• Share-able communication pins such as I2C (SDA & SCL), and SPI (MISO [D11], MOSI [D12] & SCK [D13]) will not cause a conflict between modules. As they are designed to work as a share-able communication bus.
• Non share-able communication pins such as UART (TX_ & RX_) will cause a conflict between modules to attempt to use the same pins. As UART is not a shared communication bus.
• The Sensor Hub makes sensors connectable to a Core module.
  • It provides connectivity to almost all of the pins on the Core module.
  • Be cautious when connecting a Sensor / Trinket to the Sensor Hub as that particular pin could be used by non-Core module in the build / project.
  • Visit the Sensor Hub page for information on how a Sensor / Trinket will map to a Core module based on the labeling.

Module

BUS

I2CAddr (7bit)

D0

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

A0

A1

A2

A3

SDA

SCL

A6

A7

5V

3V3

RST

AREF

Core Modules

Core

RX0

TX0

MISO

MOSI

SCK

A4

A5

IN

(IN)

RST

AREF

Core+

RX0

TX0

RX1

TX1

MISO

MOSI

SCK

SDA

SCL

IN

(IN)

RST

AREF

CoreUSB

RX1

TX1

MISO

MOSI

SCK

SDA

SCL

IN

OUT

RST

AREF

CoreRF

RX0

TX0

RX1

TX1

MISO

MOSI

SCK

SDA

SCL

IN

IN

RST

AREF

Core Programmers

BLE Upload

UART

TX

RX

IN

OUT

mBattery

UART

TX

RX

OUT

OUT

OUT

USBTTL

UART

TX

RX

OUT

OUT

OUT

USBttlC

UART

TX

RX

OUT

OUT

OUT

Function Modules

Audio

UART

(TX)

(RX)

TX

RX

(TX)

(RX)

ADKEY

OUT

IN

AudioPro

Battery Management

GPS

UART

(TX)

(RX)

TX

RX

IN

mBattery

UART

TX

RX

OUT

OUT

OUT

Motion

I2C

0x68(MPU) 0x1E(HMC) 0x77(BMP)

(INT)

(INT)

SDA

SCL

IN

SD

SPI

CS

MISO

MOSI

SCK

(CD)

IN

RTC

I2C

0x51(pcf) 0x50(eep)

INT

(INT)

SDA

SCL

(IN)

IN

Communication Modules

Bluetooth (BLE)

UART

TX

RX

(TX)

(RX)

(TX)

(RX)

IN

BLE Upload

UART

TX

RX

IN

OUT

NFC

I2C

0x24

SDA

SCL

IN

WiFi

UART

TX

RX

(TX)

(RX)

IN

RST

Extension Modules

Amplifier

(RIN)

(LIN)

IN

Hub

Motor

LED Matrix

DI

(DI)

(DI)

IN

OLED

Known Conflicts

mCookie Motor

• mCookie SD - Pin D7

mCookie SD

• mCookie Motor - Pin D7