Difference between revisions of "Clap Light Project (X02)"

From Microduino Wiki
Jump to: navigation, search
(Required Materials)
(Program)
Line 35: Line 35:
  
 
//The maximum loudness between the two claps
 
//The maximum loudness between the two claps
const uint16_t SLIENT_LOUDNESS_THRESHOLD = 200;
+
const uint16_t SILENT_LOUDNESS_THRESHOLD = 200;
  
 
volatile uint16_t mic_value;
 
volatile uint16_t mic_value;
Line 66: Line 66:
 
     mic_value = analogRead(mic_value);
 
     mic_value = analogRead(mic_value);
 
     Serial.println(mic_value);
 
     Serial.println(mic_value);
     //If the value is under the threshold, then it is slient
+
     //If the value is under the threshold, then it is silent
     if ( mic_value < SLIENT_LOUDNESS_THRESHOLD ) {
+
     if ( mic_value < SILENT_LOUDNESS_THRESHOLD ) {
 
       Serial.println("Slience detected!");
 
       Serial.println("Slience detected!");
 
       //wait a bit of time beforce looking for the second clap
 
       //wait a bit of time beforce looking for the second clap
Line 105: Line 105:
 
}
 
}
 
</source>
 
</source>
 +
==Tweaking==
 +
'''CLAP_LOUDNESS_THRESHOLD''' will change the clapping loudness trigger point. 0 ~ 1023.
 +
'''SILENT_LOUDNESS_THRESHOLD''' will change the silent registry level. 0~1023
  
 
=Usage=
 
=Usage=
 
Clap once, wait about 1-2 seconds, then clap another time. The LED should turn on. Repeating the sequence will turn off the LED.
 
Clap once, wait about 1-2 seconds, then clap another time. The LED should turn on. Repeating the sequence will turn off the LED.

Revision as of 01:28, 30 December 2016

About

This project uses the Microphone to detect clapping noises and turns on or off the LED if it senses two claps with a second pause inbetween. This project was designed for the second generation mCookie Maker kits (102 Basic, 202 Advanced and 302 Expert kits).


Required Materials

  • 1 x mCookie Core
  • 1 x mCookie USB TTL (102 Kit) or 1 x mBattery (202/302 Kit)
  • 1 x mCookie Sensor Hub
  • 1 x Single ColorLED
  • 1 x Microphone Sensor
  • 1 x Buzzer
  • 3 x Sensor Cable
  • 1 x MicroUSB Cable

Build

  1. Connect the Single ColorLED to the Sensor Hub on Pin A0/A1
  2. Connect the Buzzer to the Sensor Hub on Pin 6/7
  3. Connect the Microphone to the Sensor Hub on Pin A2/A3
  4. Grab the mCookie USBTTL or mBattery and Stack the mCookie Core on top.
  5. Stack the mCookie Sensor on top of that.
  6. Plug in the MicroUSB cable to the mCookie USBTTL or mBattery to a computer.

Program

Copy and paste the code below and upload.

#include <Adafruit_NeoPixel.h>  //Import the library for the ColorLED.
#include <stdint.h>

#define MIC_PIN A2
#define BUZZER_PIN 6
#define LED_PIN A0

//The minimum amount of clap loudness to be registered as a clap
const uint16_t CLAP_LOUDNESS_THRESHOLD = 400;

//The maximum loudness between the two claps
const uint16_t SILENT_LOUDNESS_THRESHOLD = 200;

volatile uint16_t mic_value;
unsigned long second_clap_timer;

bool leds_are_on = false;


void setup() {
  pinMode(LED_PIN, OUTPUT);
  
  Serial.begin(9600);
  // put your setup code here, to run once:
  pinMode(MIC_PIN, INPUT);
  pinMode(BUZZER_PIN, OUTPUT);

}

void loop() {
  // put your main code here, to run repeatedly:


  //Take in mic reading for the first clap
  uint16_t mic_value = analogRead(MIC_PIN);
  //Check if it is greater than the threadhold
  if ( mic_value > CLAP_LOUDNESS_THRESHOLD ) {
    Serial.println("First clap detected!");
    delay(1000); //Wait 500 milliseconds
    //Read in a new mic value for the silence between the claps
    mic_value = analogRead(mic_value);
    Serial.println(mic_value);
    //If the value is under the threshold, then it is silent
    if ( mic_value < SILENT_LOUDNESS_THRESHOLD ) {
      Serial.println("Slience detected!");
      //wait a bit of time beforce looking for the second clap
      delay(1000);
      second_clap_timer = millis();
      while(((millis() - second_clap_timer) < 2000)){
        mic_value = analogRead(MIC_PIN);
        if(mic_value > CLAP_LOUDNESS_THRESHOLD){
          Serial.println("Second clap detected!");
          tone(BUZZER_PIN, 3038, 200);
          if( leds_are_on == false ){
            activate_light();
          }
          else{
            deactivate_light();
          }
          delay(1000);
          break;
        }
      }
      
    }
  }

  delay(1);
}

void activate_light() {
  digitalWrite(LED_PIN, HIGH);
  leds_are_on = true;
}

void deactivate_light() {
  digitalWrite(LED_PIN, LOW);
  leds_are_on = false;
  return;
}

Tweaking

CLAP_LOUDNESS_THRESHOLD will change the clapping loudness trigger point. 0 ~ 1023. SILENT_LOUDNESS_THRESHOLD will change the silent registry level. 0~1023

Usage

Clap once, wait about 1-2 seconds, then clap another time. The LED should turn on. Repeating the sequence will turn off the LED.