Difference between revisions of "Lesson 9--Microduino "DIY Multimeter""

From Microduino Wiki
Jump to: navigation, search
(Result)
 
(4 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{Language|Microduino_做0-5V量程的电压表(万用表的使用)/zh}}
+
{{Language|第九课--Microduino_做0-5V量程的电压表(万用表的使用)}}
 
{| style="width: 800px;"
 
{| style="width: 800px;"
 
|-
 
|-
 
|
 
|
 
==Objective==
 
==Objective==
We have introduced the reading (0-1024) of the analog port before. Now, we will use the analog port of microduino to make a multimeter with the range of 0-5 V.
+
Previously, we introduced analogRead() and its return values of 0~1024. In this lesson, we will use the analog port of [[Microduino-Core]] to make a multimeter with the range of 0-5 V.
  
'''Notice: The circuit design of the experiment has no relatively complicated protection circuit. So please don't use more than two AA batteries and don't use the circuit to measure the lithium battery or other power supply!!'''
+
'''Important: The design of this experiment does not have an effective protection circuit. Please do not use more than two AA batteries and do not use the circuit to measure a lithium battery or any other power supply!'''
  
 
==Equipment==
 
==Equipment==
Line 12: Line 12:
 
*'''[[Microduino-FT232R]]'''
 
*'''[[Microduino-FT232R]]'''
 
*Other hardware equipment
 
*Other hardware equipment
**Breadboard Jumper            one box    
+
**1x AA Battery
**Breadboard               one piece 
+
**1x Box of breadboard jumper wires    
**1kΩ resistor       one
+
**1x Breadboard                
**USB Data cable               one
+
**1x 1kΩ resistor        
 +
**1x USB Data cable      
  
 
[[File:lesson9All.jpg|600px|center|thumb]]
 
[[File:lesson9All.jpg|600px|center|thumb]]
  
==Experimental schematic==
+
==Experiment Schematic==
 
[[File:less0n9-schematic.jpg|center|600px|thumb]]
 
[[File:less0n9-schematic.jpg|center|600px|thumb]]
The purpose of using 1K resistor is that in the case of measuring end vacant, the GND reference guide to measure port, and avoid vacant interfaces interference.
 
  
 
==Program==
 
==Program==
Line 28: Line 28:
 
void setup()
 
void setup()
 
{
 
{
   Serial.begin(115200);    //Set baud rate 9600
+
   Serial.begin(9600);    //Set baud rate 9600
 
}
 
}
 
void loop()
 
void loop()
Line 34: Line 34:
 
   
 
   
 
   int V1 = analogRead(A0);                     
 
   int V1 = analogRead(A0);                     
// Read the voltage date form A0 and stores in V1, the voltage range is 0-5v and return value is 0-1024.  
+
// Read the voltage data from A0 and store it in variable V1. The voltage range is 0-5V and returns values 0-1024.  
 
   float vol = V1*(5.0 / 1023.0);               
 
   float vol = V1*(5.0 / 1023.0);               
//Convert the V1 to actual voltage value and stores in vol
+
//Convert the V1 to the voltage value and store it in vol
 
   if (vol == temp)                             
 
   if (vol == temp)                             
 
//Use to filter duplicate data, Only the voltage value and the last isn't same then output the value.
 
//Use to filter duplicate data, Only the voltage value and the last isn't same then output the value.
Line 51: Line 51:
 
}
 
}
 
</source>
 
</source>
We don't use the function map() to the conversion, you can try it by yourself.
+
We didn't use the map() function in this example, but you can try it yourself!
  
 
==Result==
 
==Result==
When the measured voltage changed, refresh the date every 1s. If there is a gap between two voltage value, this is normal.
+
When the measured voltage changes, refresh the data every second. It is normal if there is a difference between two measurements of the same battery. This is because this is still simply a low accuracy test. If you need a high accuracy test, you can take a look at:
Because this is a low accuracy test. If you need a high accuracy test, please refer to:
 
 
http://www.hacktronics.com/Tutorials/arduino-current-sensor.html
 
http://www.hacktronics.com/Tutorials/arduino-current-sensor.html
  
 
[[File:lesson9Result.jpg|600px|center|thumb]]
 
[[File:lesson9Result.jpg|600px|center|thumb]]
 +
 
==Video==
 
==Video==
 +
https://www.youtube.com/watch?v=bhaj_QhRE-Q
 
|}
 
|}
 
https://www.youtube.com/watch?v=bhaj_QhRE-Q
 

Latest revision as of 00:49, 27 July 2015

Language: English  • 中文

Objective

Previously, we introduced analogRead() and its return values of 0~1024. In this lesson, we will use the analog port of Microduino-Core to make a multimeter with the range of 0-5 V.

Important: The design of this experiment does not have an effective protection circuit. Please do not use more than two AA batteries and do not use the circuit to measure a lithium battery or any other power supply!

Equipment

Lesson9All.jpg

Experiment Schematic

Less0n9-schematic.jpg

Program

float temp;   // Define a float variable temp to save data.
void setup()
{
  Serial.begin(9600);     //Set baud rate 9600
}
void loop()
{
 
  int V1 = analogRead(A0);                    
// Read the voltage data from A0 and store it in variable V1. The voltage range is 0-5V and returns values 0-1024. 
  float vol = V1*(5.0 / 1023.0);               
//Convert the V1 to the voltage value and store it in vol
  if (vol == temp)                             
//Use to filter duplicate data, Only the voltage value and the last isn't same then output the value.
  {
    temp = vol;                               //Compared, then store in temp variable "temp"
  }
  else
  { 
    Serial.print(vol);                       //Serial output voltage, nowrap  
    Serial.println(" V");                    //Serial output character "V", and wrap
    temp = vol;
    delay(1000);                           //Wait for 1s, use to refresh the data
  }
}

We didn't use the map() function in this example, but you can try it yourself!

Result

When the measured voltage changes, refresh the data every second. It is normal if there is a difference between two measurements of the same battery. This is because this is still simply a low accuracy test. If you need a high accuracy test, you can take a look at: http://www.hacktronics.com/Tutorials/arduino-current-sensor.html

Lesson9Result.jpg

Video

https://www.youtube.com/watch?v=bhaj_QhRE-Q