Difference between revisions of "Microduino-Joypad Getting start"
From Microduino Wiki
| Line 4: | Line 4: | ||
===硬件搭建=== | ===硬件搭建=== | ||
*步骤一：将Microduino-TFT安装在Microduino-Joypad面板上； | *步骤一：将Microduino-TFT安装在Microduino-Joypad面板上； | ||
| − | [[File:Microduino_Joypad_TFT.jpg||600px|center|thumb]] | + | [[File:Microduino_Joypad_TFT-1.jpg||600px|center|thumb]] |
*步骤二：将尼龙螺丝安装在Microduino-Joypad上，并且将底面板粘贴在Microduino-Joypad底部； | *步骤二：将尼龙螺丝安装在Microduino-Joypad上，并且将底面板粘贴在Microduino-Joypad底部； | ||
| − | [[File:Microduino_Joypad_nilong.jpg||600px|center|thumb]] | + | [[File:Microduino_Joypad_nilong-1.jpg||600px|center|thumb]] |
*步骤三：将Microduino-TFT与Microduino-Joypad通过转接线连接起来； | *步骤三：将Microduino-TFT与Microduino-Joypad通过转接线连接起来； | ||
| − | [[File: | + | [[File:Microduino_Joypad_1.jpg||600px|center|thumb]] |
*步骤四：将电池盒连接到底板上，注意正负极别接反了，板子背面标注了正负极； | *步骤四：将电池盒连接到底板上，注意正负极别接反了，板子背面标注了正负极； | ||
Revision as of 16:49, 13 November 2014
硬件搭建
测试
程序说明
//光照----------------------
Joypad.readLightSensor();
//麦克风--------------------
Joypad.readMicrophone();
//INTA----------------------
Joypad.readIntA();
//INTB----------------------
Joypad.readIntB();
//左模拟摇杆----------------
Joypad.readJoystickX();
Joypad.readJoystickY();
//右模拟摇杆----------------
Joypad.readJoystick1X();
Joypad.readJoystick1Y();
Joypad.readButton(byte ch);
//左模拟摇杆----------------
JOYSTICK_UP;
JOYSTICK_DOWN;
JOYSTICK_LEFT;
JOYSTICK_RIGHT;
//左模拟摇杆按下------------
CH_JOYSTICK_SW
//右模拟摇杆----------------
JOYSTICK1_UP;
JOYSTICK1_DOWN;
JOYSTICK1_LEFT;
JOYSTICK1_RIGHT;
//右模拟摇杆按下------------
CH_JOYSTICK1_SW
//拨档开关------------------
CH_SWITCH_L;
CH_SWITCH_R;
//四组按键------------------
CH_SWITCH_1;
CH_SWITCH_2;
CH_SWITCH_3;
CH_SWITCH_4;
//==========================
//蜂鸣器---------------------
Joypad.tone(unsigned int freq);
Joypad.tone(unsigned int freq, unsigned long duration);
Joypad.noTone();
//振动------------------------
Joypad.motor(unsigned int motor_vol);
“unsigned int motor_vol”：振动强弱开始应用 |
