Difference between revisions of "Microduino Enc Wired network experiment -302KIT"

From Microduino Wiki
Jump to: navigation, search
(Bill of Materials)
(Debugging)
Line 54: Line 54:
 
Step 1:Set up router network
 
Step 1:Set up router network
  
Power on router, and connect the PC to network.
+
Power the router and connect the PC to network.  
  
Step 2:Set up hardware
+
Step 2: Build the hardware
  
Install all Microduino module, use the extension board Microduino Duo-V for easy debugging.
+
Install all Microduino modules needed and adopt the extension board Microduino Duo-V for easy debugging.
 
|-
 
|-
 
|
 
|
Line 65: Line 65:
 
|-
 
|-
 
|
 
|
Step 3:Downlaod program
+
Step 3: Download program
  
Start Arduino IED, open the Microduino example program, board type choose "Microduino Core (Atmega328P@16M,5V)", download directly.
+
Start Arduino IED, open the Microduino example program and choose the board "Microduino Core (Atmega328P@16M,5V)", then download directly.
  
Step 4:Connect the network cable
+
Step 4:Connect the network  
  
Connect the microduino RJ45 to LAN port of router.
+
Connect Microduino-RJ45 to the LAN port of router.
  
Step 5:Control the LED in loacal network
+
Step 5:Wired control of the LED lights inside the LAN
  
Open a new web page, enter into the address "myip". Microduiono networking success can enter the control interface, or can not be opened.
+
Open a new page and enter the "myip" address in the program.You can only enter the control interface when Microduino connects the internet successfully. Otherwise, it can not be opened.  
 
|-
 
|-
 
|
 
|
Line 81: Line 81:
 
|-
 
|-
 
|
 
|
 +
 
==Result==
 
==Result==
 
Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.
 
Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.

Revision as of 08:09, 22 August 2014

Language: English  • 中文

Outline

Project: Microduino-Enc Wired Networking Experiment

Objective:Enable Microduihno-Core to connect with the network via Microduino-Enc and Microduino-RJ45, control four LED lights inside the LAN and achieve network control.

Difficulty:Elementary

Time-consuming:One hour

Maker:Microduino Studio-YLB

Bill of Materials

  • Microduino equipment:
Module Number Function
Microduino-Core(Microduino Core+) 1 Served as the slave machine,receiving and controlling signal
Microduino FT232R 1 For program download
Microduino Enc(Microduino Rj45) 2 For wireless communication
  • Other equipment:
Router one
Network cable one
micro USB cable one
LED Four
Bread board one
Breadboard jumper one box
302KIT-module

Document

Debugging

Step 1:Set up router network

Power the router and connect the PC to network.

Step 2: Build the hardware

Install all Microduino modules needed and adopt the extension board Microduino Duo-V for easy debugging.

302KIT-module
302KIT-system

Step 3: Download program

Start Arduino IED, open the Microduino example program and choose the board "Microduino Core (Atmega328P@16M,5V)", then download directly.

Step 4:Connect the network

Connect Microduino-RJ45 to the LAN port of router.

Step 5:Wired control of the LED lights inside the LAN

Open a new page and enter the "myip" address in the program.You can only enter the control interface when Microduino connects the internet successfully. Otherwise, it can not be opened.

Myip

Result

Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.

Note

  • Microduino Enc must be used with Microduino RJ45 together.
  • Need configure the MAC address and ip address in local network.

Video

http://v.youku.com/v_show/id_XNjY1Njg5Nzcy.html