Difference between revisions of "Nightlight Project (X02)"

From Microduino Wiki
Jump to: navigation, search
(Build)
(Tweaking)
Line 44: Line 44:
 
Variables can be edited to change the threshold / detection value for various functions to better fine tune to your environment.  
 
Variables can be edited to change the threshold / detection value for various functions to better fine tune to your environment.  
  
'''CLAP_LOUDNESS_THRESHOLD''' will change the clapping loudness trigger point. Lower values means a weaker noise level is detected as a clap.  
+
'''MAX_BRIGHTNESS''' will change the maximum brightness value. Range between 0 (off) and 255 (blindingly bright). Please be cautious with values above 40.
*Adjustable between 0 ~ 1023
+
*Adjustable between 0 ~255
*Default is 400
+
*Default is 40
  
'''SILENT_LOUDNESS_THRESHOLD''' will change the silent registry level. Higher values will mean that higher noise levels will be registered as a silence.
+
'''BRIGHTNESS_SCALAR''' will change the value that the brightness increases by each press of the touch sensor.
*Adjustable between 0 ~ 1023
+
*Default is 10
*Default is 200
 
  
'''PAUSE_TIME''' will change the time in which you are required to pause between claps in milliseconds. Lower values will detect faster claps, but there is settling time on the Microphone, which means too short of a pause time won't be detectable as silence.  
+
'''DEFAULT_BRIGHTNESS''' will change the default brightness should be less than the Max Brightness. This is how bright the LED Matrix will be at an minimum regardless of the input.
* Default is 200 milliseconds (1/5 of a second)
+
*Adjustable between 0~255 -- should be less than MAX_BRIGHTNESS
 +
*Default is 0 (off)
 +
 
 +
'''PRESS_DELAY'' will change how long between button presses before register another button press to switch between brightness levels. In milliseconds.
 +
*Default is 1000 -- 1 second
  
 
=Usage=
 
=Usage=
 
Clap once, wait about 1 second, then clap another time. The LED should turn on and a beep noise will occur. Repeating the sequence will turn off the LED.
 
Clap once, wait about 1 second, then clap another time. The LED should turn on and a beep noise will occur. Repeating the sequence will turn off the LED.

Revision as of 00:12, 2 March 2017

File:Nightight Project.jpg
Nightlight Project Build

About

This project uses the Light Sensor to detect ambient light and turns on or off the LED Matrix depending how dark it is in the room.

This project was designed for the second generation mCookie Maker kits (102 Basic, 202 Advanced and 302 Expert kits).

Required Materials

  • 1 x mCookie Core
  • 1 x mCookie USB TTL (102 Kit) or 1 x mBattery (202/302 Kit)
  • 1 x mCookie Sensor Hub
  • 1 x LED Matrix
  • 1 x Light Sensor
  • 1 x Touch Button
  • 2 x Sensor Cable
  • 1 x MicroUSB Cable

Build

NOTE: When connecting sensor wires, push on the plastic connector and not on the wires. Pushing on the wire can damage them.

  1. Connect the Light Sensor to the Sensor Hub on Pin A2/A3
  2. Connect the Touch Button to the Sensor Hub on Pin 2/3
  3. Grab the mCookie USBTTL or mBattery and Stack the mCookie Core on top.
  4. Stack the mCookie LED Matrix on top of that.
  5. Stack the mCookie Sensor on top of that.
  6. Plug in the MicroUSB cable to the mCookie USBTTL or mBattery to a computer.

Program

1. Connect mCookie Core to the PC with the USB Cable. Open the Microduino IDE.

2. Copy and paste the code below and upload.

3. Select the board, processor and port:

  • Go to Tools > Board and select Microduino/mCookie-Core (328p)
  • Go to Tools > Processor and select Atmega328P16M,5V
  • Go to Tools > Port and select the available port

4. Upload the program by clicking on the right arrow icon on the top left of the window. Or under Sketch > Upload.

Debugging

  • Open the Serial monitor. Information will print out when the first clap is detected as "First clap detected!".
  • Then a value will print out which is the silent value. If it is under the threshold, "Silence detected!" will print.
  • "Second clap detected!" will print if it detected a second clap.

Tweaking

Variables can be edited to change the threshold / detection value for various functions to better fine tune to your environment.

MAX_BRIGHTNESS will change the maximum brightness value. Range between 0 (off) and 255 (blindingly bright). Please be cautious with values above 40.

  • Adjustable between 0 ~255
  • Default is 40

BRIGHTNESS_SCALAR will change the value that the brightness increases by each press of the touch sensor.

  • Default is 10

DEFAULT_BRIGHTNESS will change the default brightness should be less than the Max Brightness. This is how bright the LED Matrix will be at an minimum regardless of the input.

  • Adjustable between 0~255 -- should be less than MAX_BRIGHTNESS
  • Default is 0 (off)

'PRESS_DELAY will change how long between button presses before register another button press to switch between brightness levels. In milliseconds.

  • Default is 1000 -- 1 second

Usage

Clap once, wait about 1 second, then clap another time. The LED should turn on and a beep noise will occur. Repeating the sequence will turn off the LED.