Difference between revisions of "Microduino-Module CoreSTM32"

From Microduino Wiki
Jump to: navigation, search
(Features)
(Documents)
Line 42: Line 42:
  
 
==Documents==
 
==Documents==
Microduino- CoreSTM32 used components.
+
*Main components used in Microduino- CoreSTM32
** MCU: '''[[media: STM32F103CBT6.pdf| STM32F103CBT6]]'''
+
** MCU: '''[[media: STM32F103CBT6.pdf| STM32F103CBT6]]'''
 +
**Schematic diagram: [[media:Microduino-CoreSTM32.zip| Microduino-CoreSTM32]]'''
  
 
==Development==
 
==Development==

Revision as of 05:54, 29 August 2016

Language: English  • 中文
Microduino- CoreSTM32

Microduino-CoreSTM32 is one of the core modules of Microduino, adopting ARM development board of STM32F103CBT6 chip. Microduino-CoreSTM32 is a open-source software, compatible with Maple Mini, and it can be used together with Microduino extension modules and other electronic components, modules, and sensors to make many funny interactive works.

Features

  • Small, cheap, stackable, and open;
  • Open source hardware circuit design and programming development environment similar to Arduino.
  • Microduino-CoreSTM32 can work with Microduino-USBTTL and burn programs into the bootloader flexibly.
  • With an uniform Microduino interface standard and rich peripheral modules, it can be easily connected with other Microduino modules and sensors.
  • 2.54mm-spacing female connector interface,which makes it easy to integrate to the pegboard.

Specification

Electrical Specification

  • Microcontroller: STM32F103CBT6
  • Frequency: 72MHz
  • Operation voltage: 5V
  • Core voltage: 3.3V
  • Flash: 128KB
  • SRAM: 20KB

Pin Specification

  • Digital I/O pin:

0,1,2,3,4,5,6,7,8,9,10,11,12,13,14(A0),15(A1),16(A2),17(A3),18(SDA),19(SCL),20(A6),21(A7)

  • Analog input pin:

A0(ADC12_IN0), A1(ADC12_IN1), A2(ADC12_IN2), A3(ADC12_IN3), 10(ADC12_IN4), 13(ADC12_IN5), 12(ADC12_IN6), 11(ADC12_IN7), A6(ADC12_IN8), A7(ADC12_IN9)

  • Serial port:
    • Serial RX0 and TX1, used for receiving(RX) and sending(TX) TTL serial data.
    • Serial1 D2(RX3)and D3(TX3), used for receiving(RX) and sending(TX) TTL serial data.
  • Hardware PWM: 0, 1, 4, 11, 12, 14(A0), 15(A1), 16(A2), 17(A3), 18(SDA), 19(SCL), 20(A6), 21(A7)
  • SPI: D10(SPI1_NSS), D11(SPI1_MOSI), D12(SPI1_MISO), D13(SPI1_SCK);
  • IIC: 18(SDA), 19(SCL);
  • Each I/O port has interruption function.
Microduino-Core STM-Pinout
Microduino-Core STM-Pinout
Microduino-Core STM-Pinout

Documents

Development

Set up the Microduino-CoreSTM32 development environment

  • Use the Maple IDE development environment: Microduino use the similar development environment with the Arduino IDE, so you can use the Maple IDE, Flash or Processing and so on. Combine with other Microduino module, you can finish more interesting projects.
  • Download the program to Microduino-CoreSTM32, you must use the Microduino-USB2TTL module.
  • Configure the Maple IDE, please refer to Microduino-CoreSTM32 Maple Drive Install

Program for Microduino-CoreSTM32

  • Make sure installed the Microduino-CoreSTM32 derive
  • Prepared hardware:Microduino-CoreSTM32, USB cable
  • Prepared software:Maple IDE

The beginning of Micoduino-CoreSTM32

Burn the Microduino- CoreSTM32 BootLoader

Applicaion

Microduino CoreSTM32 Tutorial

History

Picture