Difference between revisions of "Sensor-Servo Connector"

From Microduino Wiki
Jump to: navigation, search
(→‎Introduction of Pins)
 
Line 18: Line 18:
 
The servo can not link with the extension module (hub) directly, so a servo connector is needed. The servo connector have 3 above pins and 3 below pins, which can connect to two servos at the same time.  
 
The servo can not link with the extension module (hub) directly, so a servo connector is needed. The servo connector have 3 above pins and 3 below pins, which can connect to two servos at the same time.  
 
[[File:anywhere_Servo-Servo Connector.jpg|600px|center]]
 
[[File:anywhere_Servo-Servo Connector.jpg|600px|center]]
−
When connecting the servo and the sevo connector, please pay attention to the "positive and negative" , and make sure that the GND, VCC, and 1/2 three wires are connected rightly. The above pins is corresponding to the odd pins of Hub, and the below pins is corresponding to the event pins of Hub. For example, when connecting the servo to the 6/7 pin of Hub, if the servo is connected to the below pins, the control pin is 6; to the above pins is 7.  
+
When connecting the servo and the servo connector, please pay attention to the "positive and negative" , and make sure that the GND, VCC, and 1/2 three wires are connected rightly. The above pins is corresponding to the odd pins of Hub, and the below pins is corresponding to the event pins of Hub. For example, when connecting the servo to the 6/7 pin of Hub, if the servo is connected to the below pins, the control pin is 6; to the above pins is 7.  
 
[[File:anywhere_Servo-Servo Connector1.jpg|600px|center]]
 
[[File:anywhere_Servo-Servo Connector1.jpg|600px|center]]
  

Latest revision as of 07:03, 4 August 2017

Language: English  • 中文
Sensor-Servo_Connector

The product number of Sensor-Servo Connector is: MSDO41

Sensor-Servo Connector is used to link the servo with the interface of extension module.

Introduction of Pins

Sensor backpin.png

Servo Connector
General Pin Out Sensor / Trinket's Pin Out
PIN1 (GND) GND
PIN2 (VCC) VCC
PIN3 (SIGNAL-A) Digital Output (Servo Signal 1)
PIN4 (SIGNAL-B) Digital Output (Servo Signal 2)
  • General Pin Out is the standard pin out of a Sensor / Trinket connector.
  • Sensor / Trinket's Pin Out is this specific Sensor / Trinket's wiring in relation to the General Pin Out.
  • SIGNAL-A / SIGNAL-B are signals that could be digital input, digital output, analog input or analog output. Or special signals such as serial communication (SoftwareSerial, IIC (I2C), etc) or other special signals.
  • Not Connected refers to the Pin not being used for this particular Sensor / Trinket.
  • Read more about the hub module.

The servo can not link with the extension module (hub) directly, so a servo connector is needed. The servo connector have 3 above pins and 3 below pins, which can connect to two servos at the same time.

Anywhere Servo-Servo Connector.jpg

When connecting the servo and the servo connector, please pay attention to the "positive and negative" , and make sure that the GND, VCC, and 1/2 three wires are connected rightly. The above pins is corresponding to the odd pins of Hub, and the below pins is corresponding to the event pins of Hub. For example, when connecting the servo to the 6/7 pin of Hub, if the servo is connected to the below pins, the control pin is 6; to the above pins is 7.

Anywhere Servo-Servo Connector1.jpg

Application

Used to connect up to 2 Servos to the 4 pin header on a Sensor Hub.

Purchase

Gallery

File:Sensor-Servo Connector-F.JPG
Sensor-Servo Connector Front
File:Sensor-Servo Connector-b.JPG
Sensor-Servo Connector Back
Retrieved from "https://wiki.microduinoinc.com/index.php?title=Sensor-Servo_Connector&oldid=21503"