Difference between revisions of "Open Source Music Player"

Overview

• Project name：Microduino open source player
• Objective：To read the songs in the SD card.
• Difficulty: Medium
• Time consuming: 2 hours
• Maker：
• Introduction:
  • Open source music player is an open source speaker which can read SD card and decode it.
  • Appearance concise, simple button design, OLED screen display, easy to use.
  • This system is fully realized by Microduino, and the user can experience the fun of manual DIY.

Bill of materials

Programs to download

• The code of music player Github:Simple_Player_v2

Programming

• Stack Microduino-Core and Microduino-USBTTL together.
  • Connect the Microduino-USBTTL ready to upload program with a data line.
  • Note：It is best not to put all modules stacked together and then upload.
• Open Arduino IDE for Microduino, environment, （Reference of the set-up：AVR Core: Getting Started）.
• Click[Instrument], assure the board card(Microduino-Core) processor(Atmega328P@16M,5V) selected correctly, and select the corresponding port number(COMX).
• Click[File]->[Open], browse to the project program address, and click "Simple_player_V2.ino" to open program.
• After all these items are correct, click the button "→"to download the program to the development board.

Store audio

• Audio files need to be stored in a container in advance, then the player can play on them. There are two types of storage:
  • The module board FLASH：Microduino-Audio has boarded the 4MByte FLASH.
    • Audio storage method please refer to the following page: #.E5.BC.80.E5.8F.91 Download audio
  • SD outside enlarge capacity: Use the Shield module of the Microduino-Audio module to realize MicroSD card dilatation.
    • SD card supports 32GB capacity maximumly.

Steps of the set-up

Step1： According to the picture 1-1, fix Microduino-OLED on Structure-A1 with nylon screw and nylon nut . Note: Pay attention to the installation direction of the OLED display screen, and please take the LOGO Microduino as a reference, the LOGO located in the positive direction saying it installed in the right direction.

After the installation of the OLED display screen, please put nthe sensor lin access to the interface on the reverse of the OLED.

Step2： According to the picture 2-1, insert structure-D1 into the corresponding interface of the structure-B1.

According to the picture 2-2, insert structure-C2 into the corresponding interface of the structure-B1.

After step2, the player skeleton forms.

Step3： According to the picture 3-1, embed the horn into the position as shown in the picture, taking care of the installation direction of the horn, the horn line needing threading to the behind of the structure-B1 in advance.

According to the picture 3-2, splice the structure-A1 installed with OLED display screen to the front of the player skeleton, then put the structure-D3 into the slot in structure-A1 and structure-B1.

After step3, the front of the player has been assembled.

Step4： According to the picture 4-1, turn to the back of the player, stuck structure-D2 with the slot of structure-D3. Pay attention to the force evenly, avoid too much force to break, and at the same time thread the two horn line and OLED line out from the hole on the back.

According to the picture 4-2, fix the baseboard of the Microduino-Cube-S1 on the structure-C2 with nylon screw, nylon stud and nylon nut. Note that the USB port in the baseboard of the Microduino-Cube-S1needs to be out.

After step4, the construction picture is as follow:

Step5： According to the picture 5-1, insert structure-C1 into the back of the player.

According to the picture 5-2, stick structure-D4 to the corner of the structure-C1, and at the same time thread the two horn lines and OLED line out from the hole in the structure-C1.

According to the picture 5-3, overlay the following module on the baseboard of the Microduino-Cube-S1, paying attention to that install the MicroSD card on the module Shield of the Microduino-Audio in advanced. Microduino-Core Microduino-Audio Microduino-Amplifier

Step6： According to the picture 6-1, connect the OLED line to the IIC interface（There are SCL,SDA near the interface）on the left of the baseboard of the Microduino-Cube-S1. Then connect the two horn lines to the audio interface in the Microduino-Amplifiermodule.

Now open source music player has been set up completely.

Operating instruction

Player power supply

• According to the following picture, connect the USB power supply line to the USB interface in the baseboard of the Microduino-Cube-S1.
  • USB power supply can use computer USB port, USB charger, mobile power supply, and other forms.

Players use

• There is a thumb wheel switch in the shield module of the Microduino-Audio, and you can control music playing through this switch. The method is as follow:

• Player energized the default is the first song in the SD card selected, and in a suspended state, can press a allocated round to start playing music.
• The volume range of the player is 0~30. The bigger the number is, the bigger the volume is. Player chooses the volume 20 by default.

Code instruction

• The "userDef.h" is our configuration file.
• The following code can set the thumbwheel switch threshold

#define PUSH_BUTTON    50
#define LEFT_BUTTON    100
#define RIGHT_BUTTON   200

• In the event of：The volume can only be increased and can’t be reduced, the number of the song can only be increased and can’t be reduced, or on the contrary.

Cause：The thumbwheel switches threshold setting is not reasonable in the "userDef.h".

Please change the threshold in the "userDef.h" to the actual using value of the thumbwheel.

Video