Lesson 1--Microduino "LED and a Breadboard"

Language:	English  • 中文

Objective This lesson will teach you how to use Microduino to control a LED. Once you are familiar with Microduino's I/O ports, you will have developed solid fundamentals for future projects. Equipment Microduino-Core Microduino-Core is an 8-bit microcontroller development board based on Atmel ATmega328P, ATmega168PA series. It is open source and compatible with the Arduino UNO. Microduino-FT232R This module is used to upload your program into the core. You can stack it directly onto the Microduino-Core or Microduino-Core+ and communicate with your PC. Similar to many smartphones, it uses a MicroUSB as the download/upload port. Other hardware equipment: 1x Box of breadboard jumper wires 1x Breadboard 8x LEDs (Light-Emitting Diodes) 1x 220ohm resistor 1x USB Data cable Breadboard In the breadboard provided in the picture, for the two long strips in the middle，every 5 points are connected vertically. For the four strips running along the outer board, every 25 points are connected horizontally. For the outer two strips, one row is usually connected to GND and the other to VCC. Note: In some breadboards, all 50 points are connected together in the outer strips. The breadboard provided in the Microduino Basic Tutorial Kit has 30 points all connected together in the outer two strips. Be aware of the connection format when working on projects. Resistor and LED Resistors prevent your LED from being damaged by limiting the voltage supplied. Max voltage for red and green LEDs is 1.8 ~ 2.4V, blue and white is 2.8 ~ 4.2V. 3mmLED rated current is 1 ~ 10mA, 5mmLED rated current is 5 ~ 25mA, and 10mmLED rated current is 25 ~ 100mA. You can use Resistance = Voltage / Current to calculate the resistance required. 200-400 ohms of resistance is usually adequate. How to Judge the Positive/Negative Ends of a LED Light Method One: Take a look inside the LED light. The pin with a bigger bracket is negative and the one with a smaller bracket is positive. Method Two: For a new LED light, you can tell from the length of the pins. The longer pin is positive and and the shorter pin is negative. Test a LED Light via a Multimeter When using an analog multimeter to test a diode, you must choose the "Rxl0k" slot since the voltage of the battery inside the multimeter is only 1.5V when the multimeter is under the "R×lk" slot, lower than the voltage drop of a 3V LED light. In that case, it is impossible to test LED lights no matter what connection method you adopt. While the analog multimeter is under the "R×l0k" slot, you can test the LED light for the voltage of the battery is about 9V(or 15V), higher than the voltage drop. Since the black probe of the analog multimeter shows positive and the red probe shows negative, you need to connect the black probe to the positive of the LED light and the red probe to the negative. If the LED lights up, then it works. Different from the analog multimeter, the digital multimeter shows contrary electrode. Adopting the right connection method, you will know the LED is working when it lights up. Experiment Schematic There are two connection methods: Method One: Connect the positive end (anode) to Microduino digital I/O port 13 and the negative end (cathode) to GND. This creates a high level connection. Method Two: Connect the anode to Microduino digital I/O port 13 and the cathode to VCC. This creates a low level connection. Program Using delay() function: int led = 13;// Define the PIN void setup() { pinMode(led, OUTPUT); // Define the I/O port 13 as output } void loop() { digitalWrite(led, HIGH); //Set I/O port 13 output as High.In high level connection: LED will turn on; low level connection: LED will turn off delay(1000); // delay 1s digitalWrite(led, LOW); //Set I/O port 13 output as Low.In high level connection: LED will turn off; low level connection: LED will turn on delay(1000); // delay 1s } Using function millis()：Returns the number of milliseconds from when the program started running. int ledPin=13; #define TIME 1000 long time1=0,time2=0; void setup() { pinMode(ledPin,OUTPUT); } void loop() { if(millis()<time2+TIME) { digitalWrite(ledPin,HIGH); time1=millis(); } else { digitalWrite(ledPin,LOW); if(millis()>time1+TIME) time2=millis(); } } Although the code looks more complicated when using millis(), it is more efficient than the delay() function since it uses less resources and causes fewer delays on the system. It may not be of concern for now and you are free to use delay(), but when projects get large, using delay() may cause unintended lag. How To Download The Program Choose the board type in "tools". The "Microduino-Core(ATmega328P@16M，5V)" is used in this experiment. There are two types of 328 boards, so you need identify which type of board you are using. You can check the 0 resistor's connection method to identify. Choose COM port in "tools". The serial port is different for everyone's computer. It is usually ports 3-5. The COM port is in "properties"->"device manager" in your computer. You also can double-click "Advanced" to change the COM port by port settings. Compile and then download program Result After the download, you can see the LED flash once every second! Video http://v.youku.com/v_show/id_XNzEwMDA0NzA4.html