Difference between revisions of "MDesigner: Live mode"

From Microduino Wiki
Jump to: navigation, search
(Live Mode)
Line 37: Line 37:
  
  
=Live Mode=
+
=Overview=
 
'''Live''' mode is the default mode when using mDesigner. It allows the user to use mDesigner as if it was Scratch, but with the ability to use Microduino modules. The user must upload a special firmware on the Core / Core+ module first in order to use this mode. A firmware is code that runs on the core module itself. This special firmware is designed to accept commands from mDesigner directly and performs the requested commands.
 
'''Live''' mode is the default mode when using mDesigner. It allows the user to use mDesigner as if it was Scratch, but with the ability to use Microduino modules. The user must upload a special firmware on the Core / Core+ module first in order to use this mode. A firmware is code that runs on the core module itself. This special firmware is designed to accept commands from mDesigner directly and performs the requested commands.
==Communication Overview==
+
=Communication Overview=
 
The communication between mDesigner running on a computer and the project (hardware) is outlined below.
 
The communication between mDesigner running on a computer and the project (hardware) is outlined below.
 
{| style="width: 1000px; text-align:left"
 
{| style="width: 1000px; text-align:left"
Line 69: Line 69:
 
|}
 
|}
  
==Preparation==
+
=Preparation=
 
A '''firmware''' is a program that runs on core modules such as the Core and Core+. Live mode requires a special firmware to be uploaded prior to use.  
 
A '''firmware''' is a program that runs on core modules such as the Core and Core+. Live mode requires a special firmware to be uploaded prior to use.  
  
Line 76: Line 76:
 
|}
 
|}
  
===Hardware Preparation===
+
==Hardware Preparation==
 
*Ensure drivers are properly installed by following the '''[[Software_Setup:_mDesigner | mDesigner getting started guides]]'''.
 
*Ensure drivers are properly installed by following the '''[[Software_Setup:_mDesigner | mDesigner getting started guides]]'''.
 
*Connect to the computer with a USB cable with either a:
 
*Connect to the computer with a USB cable with either a:
Line 86: Line 86:
 
[[File:MDesigner_Live_Mode_Hardware_Preparation.png|550px]]
 
[[File:MDesigner_Live_Mode_Hardware_Preparation.png|550px]]
  
===Upload the Firmware===
+
==Upload the Firmware==
 
#Open mDesigner.<br>:[[File:MDesigner_Flash_Firmware_1.png|400px]]<br><br>
 
#Open mDesigner.<br>:[[File:MDesigner_Flash_Firmware_1.png|400px]]<br><br>
 
#Select the port mBattery / mCenter+ is connect to.<br>:[[File:MDesigner_Flash_Firmware_2.png|400px]]<br><br>
 
#Select the port mBattery / mCenter+ is connect to.<br>:[[File:MDesigner_Flash_Firmware_2.png|400px]]<br><br>
Line 97: Line 97:
 
::[[File:MDesigner_Live_Mode_Ready.png|400px]]
 
::[[File:MDesigner_Live_Mode_Ready.png|400px]]
  
==Usage==
+
=Usage=
 
Once your script is assembled and ready. To start your script simply click on the '''block set''' to activate it. (A '''block set''' is a connected set of blocks.)<br>If your block set has a '''When Green Flag Clicked''' block on top of it, then the block set can be activated by the '''green flag''' on the top right of mDesigner.<br>
 
Once your script is assembled and ready. To start your script simply click on the '''block set''' to activate it. (A '''block set''' is a connected set of blocks.)<br>If your block set has a '''When Green Flag Clicked''' block on top of it, then the block set can be activated by the '''green flag''' on the top right of mDesigner.<br>
 
*'''A:''' Click anywhere on the '''block set''' to activate it.
 
*'''A:''' Click anywhere on the '''block set''' to activate it.

Revision as of 19:14, 24 July 2018

mDesigner in Live mode.

The primary methods of using Microduino modules with mDesigner is with Live and Arduino mode. Each mode as it own pros and cons. Determining the right mode is up to the user per use case. Although, it is recommended to start with "Live" mode for testing then switching to "Arduino" mode later.

Live mode is regular Scratch, but with added blocks which are designed to interact with Microduino modules. This means the user has access to the stage and actor blocks. Projects (hardware) need to be connected to the computer running mDesigner. mDesigner communicates with the project (hardware), namely the Core module, in "real time" over the USB connection by sending commands for the Core module to perform. This means that "Live" mode requires a constant connection with the computer running mDesigner.

Arduino mode acts as a "visual" drag and drop coding editor. The script (code) is converted to "Arduino" code and then compile and uploaded to the attached Core module. This means that code can run even when detached from the computer. The stage and actor are disabled in this mode since the code runs independent of mDesigner.

Capability Live Mode Arduino Mode
Drag & Drop programming Yes Yes
Supports Microduino modules Yes Yes
Stage and actor enabled Yes No
Real time code testing Yes No
Code compiled and uploaded No Yes
Can run WITHOUT being connect to computer No Yes


Overview

Live mode is the default mode when using mDesigner. It allows the user to use mDesigner as if it was Scratch, but with the ability to use Microduino modules. The user must upload a special firmware on the Core / Core+ module first in order to use this mode. A firmware is code that runs on the core module itself. This special firmware is designed to accept commands from mDesigner directly and performs the requested commands.

Communication Overview

The communication between mDesigner running on a computer and the project (hardware) is outlined below.

MDesigner mBattery Live Mode.png
MDesigner Live Mode.png
Computer:
Computer running mDesigner sends commands or receives data with mBattery/mCenter+ over USB.
mBattery/mCenter+:
mBattery/mCenter+ acts as a communication bridge with the Computer (running mDesigner) and the Core/Core+ module.
Core/Core+:
  • The Core/Core+ module must be programmed with a special firmware designed to work with mDesigner. See Section Preparation
  • The Core/Core+ module receives commands from mBattery/mCenter+ which originate from the Computer running mDesigner. Core/Core+ performs the requested commands.
  • The Core/Core+ module can send back information (if requested) back to mBattery/mCenter+ which ends up at the computer running mDesigner.

Connected to Computer Requirement

In this mode, to control the modules, the user will need to have their project (hardware) connected to the computer sending commands in real time.

Note: If the project (hardware) is disconnected from the computer running mDesigner, then the project (hardware) will stop receiving commands and thus does nothing.
MDesigner mBattery Live Mode Disconnected.png
MDesigner Live Mode Disconnected.png
Computer:
Computer running mDesigner cannot send commands or receive data with mBattery/mCenter+ over USB since it is disconnected.
Core/Core+:

The Core/Core+ module is no longer receiving commands and does nothing.

Preparation

A firmware is a program that runs on core modules such as the Core and Core+. Live mode requires a special firmware to be uploaded prior to use.

Note: The special firmware only needs to be programmed once unless it is overwritten.
Using Arduino mode and uploading a program will overwrite the special firmware, thus a re-programming of the special firmware will be necessary in order to use Live mode again.

Hardware Preparation

  • Ensure drivers are properly installed by following the mDesigner getting started guides.
  • Connect to the computer with a USB cable with either a:
    • mBattery with a stacked Core / Core+ module.
    • mCenter+
  • Ensure that mBattery / mCenter+ is powered on.

MDesigner mBattery Live Mode Hardware Preparation.png


MDesigner Live Mode Hardware Preparation.png

Upload the Firmware

  1. Open mDesigner.
    :MDesigner Flash Firmware 1.png

  2. Select the port mBattery / mCenter+ is connect to.
    :MDesigner Flash Firmware 2.png

  3. Under Settings (gear icon) select Flash firmware and select mCookie. Uploading will start.
    :MDesigner Flash Firmware 3.png MDesigner Flash Firmware 4.png MDesigner Flash Firmware 5.png

  4. Once complete, select the port mBattery / mCenter+ is connected to again to begin using mDesigner with Microduino modules.
    :MDesigner Flash Firmware 6.png MDesigner Flash Firmware 2.png

Note: Ensure the top says Ready when using Live mode. This means that the hardware and mDesigner are ready.
The COM port must be re-selected if restarting mDesigner or when re-connecting the mBattery / mCenter+.
MDesigner Live Mode Ready.png

Usage

Once your script is assembled and ready. To start your script simply click on the block set to activate it. (A block set is a connected set of blocks.)
If your block set has a When Green Flag Clicked block on top of it, then the block set can be activated by the green flag on the top right of mDesigner.

  • A: Click anywhere on the block set to activate it.
  • B: Click on the Green flag to activate ALL block sets which start with the When Green Flag Clicked Block.png block (When Green Flag click block).

MDesigner Live Mode Usage 1.png


To stop all currently running blocks, click on the Stop Sign on the top right of mDesigner.

Note: Running blocks will be highlighted in yellow.

MDesigner Live Mode Usage 2.png