Difference between revisions of "Microduino Light indicator-Digital tube(TSL2561)"

From Microduino Wiki
Jump to: navigation, search
(Created page with "{{Language | Microduino 光照指示器-数码管(TSL2561)}} {| style="width: 800px;" |- | ==Objective== This tutorial will teach you to use the TSL2561 sensor and use digital...")
 
 
Line 80: Line 80:
  
 
==Debug==
 
==Debug==
Step 1:Download TSL2561 library, and uncompress it to libraries folder of Arduino IDE, then restart IDE.
+
Step 1: Download TSL2561 library, and uncompress it to libraries folder of Arduino IDE, then restart IDE.
 
http://learn.adafruit.com/tsl2561/use  
 
http://learn.adafruit.com/tsl2561/use  
  
Step 2:Copy the code to IDE and compile it.
+
Step 2: Copy the code to IDE and compile it.
  
 
Step 3: Set up circuit, as follows:
 
Step 3: Set up circuit, as follows:
Line 89: Line 89:
 
[[File:Microduino数码管关照指示器连接图(TSL2561).jpg|600px|center|thumb]]
 
[[File:Microduino数码管关照指示器连接图(TSL2561).jpg|600px|center|thumb]]
  
Step 4:Run program.
+
Step 4: Run program.
  
Step 5:Observe digital tube, cover the light sensor with the hand and then let it see the light again, look at the digital tube change.
+
Step 5: Observe digital tube, cover the light sensor with the hand and then let it see the light again, look at the digital tube change.
  
 
==Result==
 
==Result==

Latest revision as of 10:12, 28 September 2016

Language: English  • 中文

Objective

This tutorial will teach you to use the TSL2561 sensor and use digital tube to dispaly the result.

Equipment

TSL2561 light sensor:

TSL2561.jpg

Product overview TSL2561 is a light-digital converter which converts light into digital signal output, contains I2C interface or SMBus interface. Each device connected to a photosensitive diode tube and infrared photosensitive diode on a single CMOS integrated circuit. The integrated circuit has 20bit dynamic range optimal light response ability.

Features:

  • Programmable to set light intensity's threshold, when the actual light intensity exceeds the threshold sends a interrupt signal;
  • Digital output meets standard SMBus (TSL2560) and I2C (TSL2561) bus protocol;
  • Analog gain and digital output time programmable control;
  • 1.25mm x 1.75mm ultra small encapsulated, in low power mode, the power consumption only has 0.75 mW;
  • Automatic inhibition 50 Hz/60 Hz light wave.

Schematic

Microduino数码管光照指示器原理图(TSL2561).jpg

Pin table

Microduino Pin Digital tube pin 74HC595
10(A) Q0
9(B) Q1
1(C) Q2
4(D) Q3
3(E) Q4
6(F) Q5
5(G) Q6
2(DP) Q7
V5 VCC, MR
GND GND, OE
D11 DS
D10 ST_CP
D13 SH_CP
Q7’
D8 12
D4 9
D3 8
D1 6

Program

https://github.com/Microduino/Microduino_Tutorials/tree/master/Microduino_Sensor/TSL2561Segments

Debug

Step 1: Download TSL2561 library, and uncompress it to libraries folder of Arduino IDE, then restart IDE. http://learn.adafruit.com/tsl2561/use

Step 2: Copy the code to IDE and compile it.

Step 3: Set up circuit, as follows:

Microduino数码管关照指示器连接图(TSL2561).jpg

Step 4: Run program.

Step 5: Observe digital tube, cover the light sensor with the hand and then let it see the light again, look at the digital tube change.

Result

Cover the TSL2561 sensor with the hand, the digital tube's value will decrease, put the hand away, the value will increase.


Video

http://v.youku.com/v_show/id_XNjkyMzUwMDc2.html