Sensor-LAMP

Language:	English  • 中文

Feature Adopt six WS2812 lights as the optical source. An analog port can flexibly operate the color of several colored LED lights. Open hardware circuit design and Arduino compatible IDE. With uniform Microduino interface standard and rich peripheral modules, it can flexibly connect with other modules and sensor. 2.54mm (0.1 inch) pin pitch, compatible with bread boards and pegboards. Controlled by Analog port on the back with A0, A1, A2, A3, A6 and A7 for option. Microduino-RTC-Pinout1 Specification WS2812 The tricolor of each pixel can realize brightness display of 256 level and complete 16,777,216 kinds of full color display and no less than 400hz/s scanning frequency. With built-in signal shaping circuit, any pixel receives signal and then outputs after signal shaping, ensuring the circuit wave will not accumulate. Up to 800Kbps data transmission rate. Document Main componet WS2812 wiki page: http://wiki.hacdc.org/index.php/WS2811_Digital_RGB_LED#Individual_LEDs Development Arduino Library and Support Package Adafruit_NeoPixel:https://github.com/adafruit/Adafruit_NeoPixel Project Voice Control Light Debugging Program Adopt Adafruit_NeoPixel program example from Microduino IDE. Open IDE, click File→ Examples →Find LED_WS2812 #include <Adafruit_NeoPixel.h> #define PIN 6 //Define control pin // Parameter 1=Colored LED number in "strip". // Para.2=Pin number // Para.3=Colored LED type. Optional(Select one from the first two or the last two) // NEO_RGB Pixels are wired for RGB bitstream // NEO_GRB Pixels are wired for GRB bitstream // NEO_KHZ400 400 KHz bitstream (e.g. FLORA pixels) // NEO_KHZ800 800 KHz bitstream (e.g. High Density LED strip) Adafruit_NeoPixel strip = Adafruit_NeoPixel(60, PIN, NEO_GRB + NEO_KHZ800); void setup() { strip.begin(); strip.show(); //Initialize all light strips are out. } void loop() { // Method to lighten all lights. colorWipe(strip.Color(255, 0, 0), 50); // Red colorWipe(strip.Color(0, 255, 0), 50); // Green colorWipe(strip.Color(0, 0, 255), 50); // Blue rainbow(20); rainbowCycle(20); } //"c"(color); All lights get lightened in order and it takes a few seconds for the next light to get lightened before the last one. void colorWipe(uint32_t c, uint8_t wait) { for(uint16_t i = 0; i < strip.numPixels(); i++) //Get lightened in order. { strip.setPixelColor(i, c); //The function is used for lightening the "i" light strip with the "c" color. strip.show(); //The function will display the control info. written by the function "setPixelColor". delay(wait); } } void rainbow(uint8_t wait) //Rainbow display { uint16_t i, j; for(j = 0; j < 256; j++) //225 kinds of color change gradually { for(i = 0; i < strip.numPixels(); i++) //Light up the lights in sequence and wait for a few millisecond { strip.setPixelColor(i, Wheel((i + j) & 255)); } strip.show(); delay(wait); } } // Different from the function above, it adds rainbow loop. void rainbowCycle(uint8_t wait) { uint16_t i, j; for(j = 0; j < 256 * 5; j++) //The rainbow circulates for five times. { for(i = 0; i < strip.numPixels(); i++) { //Mathematical transformation added for the loop. strip.setPixelColor(i, Wheel(((i * 256 / strip.numPixels()) + j) & 255)); } strip.show(); delay(wait); } } // Enter a number within 0-225 and get the only corresponding color. // The color will change from red, green to blue and then red gradually and repeatedly. uint32_t Wheel(byte WheelPos) { if(WheelPos < 85) { return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0); } else if(WheelPos < 170) { //Since the WheelPos * 3 will surpass 255 under 85-170, it needs reduce 85 firstly. WheelPos -= 85; return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3); } else { // Since the WheelPos * 3 will surpass 255 under over 170, it needs reduce 170 firstly. WheelPos -= 170; return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3); } Purchase Pictures Back Back