Difference between revisions of "Microduino-Module CoreSTM32"

Microduino- CoreSTM32

Microduino-CoreSTM32 is one of core modules of Microduino series, Microduino-CoreSTM32 is an open source hardware and Maple Mini compatible. It is an 32-bit ARM Cortex-M3 development board, based on STMicroelectronics' STM32F103CBT6 chip. It can be combined with other Microduino modules and used in more projects.

Features

• Small, Stackable, Strong
• Open source hardware, using the same development environment as Arduino IDE
• Using the U-Shape 27-pin interface (UPin-27), the standard interface of Microduino series
• Microduino modules and sensors can be easily stacked and extended through it
• 2.54mm (0.1 inch) pin pitch, compatible to bread board and hole board
• Microduino-CoreSTM32 can use the Microduino-USBTTL module to burn the bootloader. Refers to

 bootloader

Specifications

• Microcontroller: STM32F103CBT6
• Speed: 72MHz
• Operating Voltage: 5V
• Core Voltage: 3.3V
• Flash: 128KB
• SRAM: 20KB
• Digital I/O Pins:0,1,2,3,4,5,6,7,8,9,10,11,12,13,14(A0),15(A1),16(A2),17(A3),18(SDA),19(SCL),20(A6),21(A7)
• Analog Input Pins: A0(ADC12_IN0),A1(ADC12_IN1),A2(ADC12_IN2),A3(ADC12_IN3),10(ADC12_IN4),13(ADC12_IN5),12(ADC12_IN6),11(ADC12_IN7),A6(ADC12_IN8),A7(ADC12_IN9)
• DC Current per I/O Pin: 40 mA
• DC Current: 50 mA
• Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data.
• Serail1: （RX3）和3（TX3). Used to receive (RX) and transmit (TX) TTL serial data.
• External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
• PWM: 0,1,4,11,12,14(A0),15(A1),16(A2),17(A3),18(SDA),19(SCL),20(A6),21(A7)
• SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication using the SPI
• IIC: 18(SDA),19(SCL)

library.

• TWI: A4 or SDA pin and A5 or SCL pin. Support TWI communication using the Wire library.
• AREF. Reference voltage for the analog inputs. Used with analogReference().
• Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader
• SRAM 2 KB (ATmega328P)
• EEPROM 1 KB (ATmega328P)
• Clock Speed 16MHz(5V) / 8Mhz(3.3V)

Documents

Microduino- CoreSTM32 used components.

• • MCU: STM32F103CBT6

Development

Set up the Microduino-CoreSTM32 development environment

• Use the Maple IDE development environment: Microduino use the similar developemnt environment with the Arduino IDE, so you can use the Maple IDE, Flash or Processing and so on. Conbine with other Microduino module, you can finish more interesting projects.
• Download the program to Microduino-CoreSTM32, you must use the Microduino-USB2TTL/zh module。
• Configure the Maple IDE, please refer to Microduino-CoreSTM32 Maple Drive Install

Program for Microduino-CoreSTM32

• Make sure installed the Microduino-CoreSTM32 derive
• Prepared hardware：Microduino-CoreSTM32、USB cable
• Prepared software：Maple IDE

The beginning of Micoduino-CoreSTM32

Burn the Microduino- CoreSTM32 BootLoader

• If you got a Microduino-CoreSTM32 board without the bootloader, you have to use the Microduino-CoreUSB to burn the bootloader firstly, please refers to Use the Microduino-CoreUSB to burn bootloader for Microduino- CoreSTM32.

Applicaion

Microduino CoreSTM32教程

History

Picture