|
|
| (One intermediate revision by one other user not shown) |
| Line 6: |
Line 6: |
| | Product number of mCookie Sensor—Hall:'''MSDS41''' | | Product number of mCookie Sensor—Hall:'''MSDS41''' |
| | | | |
| − | mCookie Sensor-Hall is a HAL49E linear hall sensor, which can detect the strength of the magnetic field. | + | mCookie Sensor-Hall is a linear hall sensor, which can detect the strength and polarity of the magnetic field. |
| | | | |
| | Sensor hall is a magnetic field sensor based on Hall effect. | | Sensor hall is a magnetic field sensor based on Hall effect. |
| | | | |
| − | Hall effect is a kind of magnetoelectric effect, which is found by Hall（A.H.Hall，1855—1938）on 1879 when he was studying the conduction mechanism of the metal. | + | Hall effect is a kind of magnetoelectric effect, which is found by Hall（A.H.Hall）on 1879 when he was studying the conduction mechanism of the metal. |
| | | | |
| | | | |
| Line 17: |
Line 17: |
| | | | |
| | ==Description of Sensor Pins== | | ==Description of Sensor Pins== |
| − | {{Sensor_explain | + | {{ST_Pinout |
| − | |nameA=[[Sensor-Hall]] | + | |st_name=Hall Sensor |
| − | |modeA=Analog signal input | + | |pin3=Analog Input |
| − | |modeB=NC
| |
| | }} | | }} |
| | | | |
| Line 26: |
Line 25: |
| | *With high detection sensitivity, and stability. | | *With high detection sensitivity, and stability. |
| | *A linear hall sensor with a polarity. | | *A linear hall sensor with a polarity. |
| − | | + | *With small size which is easy to install. |
| | | | |
| | ==Specification== | | ==Specification== |
|
|
Product number of mCookie Sensor—Hall:MSDS41
mCookie Sensor-Hall is a linear hall sensor, which can detect the strength and polarity of the magnetic field.
Sensor hall is a magnetic field sensor based on Hall effect.
Hall effect is a kind of magnetoelectric effect, which is found by Hall（A.H.Hall）on 1879 when he was studying the conduction mechanism of the metal.
Description of Sensor Pins
Hall Sensor
| General Pin Out
|
Sensor / Trinket's Pin Out
|
| PIN1 (GND)
|
GND
|
| PIN2 (VCC)
|
VCC
|
| PIN3 (SIGNAL-A)
|
Analog Input
|
| PIN4 (SIGNAL-B)
|
Not Connected
|
- General Pin Out is the standard pin out of a Sensor / Trinket connector.
- Sensor / Trinket's Pin Out is this specific Sensor / Trinket's wiring in relation to the General Pin Out.
- SIGNAL-A / SIGNAL-B are signals that could be digital input, digital output, analog input or analog output. Or special signals such as serial communication (SoftwareSerial, IIC (I2C), etc) or other special signals.
- Not Connected refers to the Pin not being used for this particular Sensor / Trinket.
- Read more about the hub module.
Features
- With high detection sensitivity, and stability.
- A linear hall sensor with a polarity.
- With small size which is easy to install.
Specification
- Size of the sensor
- Size of the board: 23.5mm*13mm;
- 1.27mm-spacing 4Pin interface connected with sensorhub;
- Sensor CAD drawings: File:Sensor CAD.zip.
- Function description
- This sensor is 10-bit ADC（0~1023）, and the static value that the pin IO1 gets is 512;
- The strength of the magnetism changes according to south and north poles;
- If get close to the hall circuit from the back with the N pole, the output voltage will reduce, and the analog value will reduce（512~0）, too;
- If get close with S pole from the back, the output voltage will increase and the analog input value will increase（512~1023）, too;
- If from the front, the output state is opposite to from the back.
- Connection
- This sensor can be connected with the following interfaces of the core: A0~A7.
Documents
Development
Program Download
Programming
Hardware Setup
- Referring to the following picture, connect the Sensor-Hall to the analog interface A0 of Microduino-Sensorhub.
Effect Observation
- After the download, open the serial port monitor.
- Get close to the hall circuit from the back with S pole. The output voltage of both ends of the hall sensor is during 2.5V~5V, and the analog value it returns is during 512~1023.
- Get close to the hall circuit from the back with the N pole. The output voltage of both ends of the hall sensor is during 2.5V~0V, and the analog value it returns is during 512~0.
- If get close to the circuit from the front, the output state is opposite to from the back.
Application
- It is suitable for the detection of magnetic field strength.
Projects
Purchase
History
Gallery
|
