Difference between revisions of "Sensor-PIR"

From Microduino Wiki
Jump to: navigation, search
(→‎Image)
 
(One intermediate revision by one other user not shown)
Line 11: Line 11:
  
 
==Introduction of Pins==
 
==Introduction of Pins==
−
{{Sensor_explain
+
{{ST_Pinout
−
|nameA=[[Sensor-PIR]]
+
|st_name=PIR Sensor
−
|modeA=Digital read
+
|pin3=Digital Input
−
|modeB=NC
 
 
}}
 
}}
−
 
  
 
==Features==
 
==Features==
Line 35: Line 33:
 
*Size
 
*Size
 
**Size of the board: 23.5mm*13mm
 
**Size of the board: 23.5mm*13mm
−
**1.27mm-spacing 4Pin itnerface connected to sensorhub
+
**1.27mm-spacing 4Pin interface connected to sensorhub
 
**The CAD drawing of the sensor: '''[[File:Sensor_CAD.zip]]'''
 
**The CAD drawing of the sensor: '''[[File:Sensor_CAD.zip]]'''
 
*Technical parameters  
 
*Technical parameters  

Latest revision as of 06:57, 4 August 2017

Language: English  • 中文
Sensor-PIR

The product number of Sensor-PIR is: MSDI51

Sensor-PIR is a pyroelectric infrared sensor that can detect infrared rays sent from moving human body or animals. It can output switch signals and be used in various occasions that need to detect moving human body.


Introduction of Pins

Sensor backpin.png

PIR Sensor
General Pin Out Sensor / Trinket's Pin Out
PIN1 (GND) GND
PIN2 (VCC) VCC
PIN3 (SIGNAL-A) Digital Input
PIN4 (SIGNAL-B) Not Connected
  • General Pin Out is the standard pin out of a Sensor / Trinket connector.
  • Sensor / Trinket's Pin Out is this specific Sensor / Trinket's wiring in relation to the General Pin Out.
  • SIGNAL-A / SIGNAL-B are signals that could be digital input, digital output, analog input or analog output. Or special signals such as serial communication (SoftwareSerial, IIC (I2C), etc) or other special signals.
  • Not Connected refers to the Pin not being used for this particular Sensor / Trinket.
  • Read more about the hub module.

Features

  • Adopt digital integrated pyroelectric infrared probe AM412.
  • With high precision and sensitivity.
  • Low power consumption, long service life and good stability.
  • Digital signals
  • Small size and easy to install.

Specification

  • Voltage
    • 3.3V~5V working voltage
  • Electrical specification
    • Working current: 15uA
    • Working temperature: -20~85℃
    • Output voltage: high level 5V, low level 0V
  • Size
    • Size of the board: 23.5mm*13mm
    • 1.27mm-spacing 4Pin interface connected to sensorhub
    • The CAD drawing of the sensor: File:Sensor CAD.zip
  • Technical parameters
    • Output delay（high level）: about 2.3~3s
    • Induction angle: 100°
    • Induction distance: 7m
  • Connection
    • This sensor can be connected to the following interfaces of core: D2~D13,A0~A7

Document

Development

Program Download

Programming

  • Follow the Software Getting Started Guide.
  • Select the Board, Processor and Port.
  • Click [File]->[Open], browse to the project program address, and click "Sensor-PIR Test.ino" to open the program.
  • After confirming all these items are correct, click "→" to download the program to the development board.

Hardware Setup

  • Referring to the following diagram, connect the Sensor-PIR to the digital pin D6 of Microduino-Sensorhub.


Microduino-sensorhub Crash.JPG


Result

  • After download, open the serial monitor.
  • The static sensor signal is LOW. After detect the IR emitted by living things within measurement range, it changes into HIGH.

Application

  • Intrusion alarm
  • Non-contact infrared automatic switch


Project

History

Gallery

File:Microduino-Passive Infrared-F1.JPG
Sensor-PIR Front
File:Microduino-Passive Infrared-b1.JPG
Sensor-PIR Back
Retrieved from "https://wiki.microduinoinc.com/index.php?title=Sensor-PIR&oldid=21502"