Difference between revisions of "Sensor-Color LED"
From Microduino Wiki
(→Programming) |
(→Programming) |
||
| (13 intermediate revisions by the same user not shown) | |||
| Line 61: | Line 61: | ||
<tab name="Arduino for Microduino" style="width:100%;"> | <tab name="Arduino for Microduino" style="width:100%;"> | ||
==Introduction== | ==Introduction== | ||
| − | The ColorLED is used as an output pin. The Adafruit_NeoPixel library '''([https://learn.adafruit.com/adafruit-neopixel-uberguide/arduino-library Read more])''' is used to control the ColorLED. | + | The ColorLED is used as an output pin. The library is based on the Adafruit_NeoPixel library '''([https://learn.adafruit.com/adafruit-neopixel-uberguide/arduino-library Read more])''' is used to control the ColorLED. Most of the functions are similar. |
==Key Functions== | ==Key Functions== | ||
| − | *Required Libraries: | + | *Required Libraries: '''Microduino_ColorLED.h''' |
*Key Functions: | *Key Functions: | ||
| − | ** ''' | + | ** Constructor: '''ColorLED strip = ColorLED(num_colorleds, colorled_pin)''' - creates the ColorLED object |
| − | ** ''' | + | ***'''num_colorleds''' - defines the number of ColorLEDs connected to the '''colorled_pin''' |
| + | ***'''colorled_pin''' - defines the pin the ColorLEDs is connected to | ||
| + | ** '''strip.begin()''' - initializes the ColorLED object | ||
| + | ** '''strip.setPixelColor(colorled_index, red_value, green_value, blue_value)''' - configures the color value for that colorled index, must call '''strip.show()''' for the ColorLED to actually display the change | ||
***'''colorled_index''' - is the index of the ColorLED to configure, first in the chain is 0, second is 1, etc | ***'''colorled_index''' - is the index of the ColorLED to configure, first in the chain is 0, second is 1, etc | ||
***'''red_value''' - red value to set, between 0 (off) and 255 (maximum on) | ***'''red_value''' - red value to set, between 0 (off) and 255 (maximum on) | ||
***'''green_value''' - green value to set, between 0 (off) and 255 (maximum on) | ***'''green_value''' - green value to set, between 0 (off) and 255 (maximum on) | ||
***'''blue_value''' - blue value to set, between 0 (off) and 255 (maximum on) | ***'''blue_value''' - blue value to set, between 0 (off) and 255 (maximum on) | ||
| − | ** ''' | + | ** '''strip.show()''' - call this function after setting the color values for the ColorLED to actually display the color |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Example== | ==Example== | ||
This is a simple example which: | This is a simple example which: | ||
| − | * | + | *Turns the ColorLED to red |
*Waits 1 second. | *Waits 1 second. | ||
| − | *Turns | + | *Turns the ColorLED to green |
*Wait 1 second. | *Wait 1 second. | ||
| − | * | + | *Turns the ColorLED to blue |
| − | *Waits | + | *Waits 1 second. |
'''Note''': Important lines of code are highlighted. | '''Note''': Important lines of code are highlighted. | ||
| − | <syntaxhighlight lang="cpp" highlight="1, | + | <syntaxhighlight lang="cpp" highlight="1-3,5,6,8,9,11,12,20,21,23,24,30-33,38-41,46-49"> |
| − | //Define the pin the | + | //Include the required libraries to control the ColorLED |
| − | const int | + | //Based on: https://learn.adafruit.com/adafruit-neopixel-uberguide/arduino-library |
| + | #include <Microduino_ColorLED.h> | ||
| + | |||
| + | //Define the pin the ColorLED is connected to | ||
| + | const int COLORLED_PIN = 6; | ||
| + | |||
| + | //Define the number of ColorLEDs daisy chained together | ||
| + | const int COLORLED_NUM = 1; | ||
| + | |||
| + | //Declare and initialize the ColorLED object | ||
| + | ColorLED strip = ColorLED(COLORLED_NUM, COLORLED_PIN); | ||
void setup() { | void setup() { | ||
| Line 104: | Line 106: | ||
//Initial serial communication port at 9600 baud | //Initial serial communication port at 9600 baud | ||
Serial.begin(9600); | Serial.begin(9600); | ||
| + | |||
| + | //Initialize the ColorLED class object | ||
| + | strip.begin(); | ||
| + | |||
| + | //Initialize all ColorLEDs to 'off' | ||
| + | strip.show(); | ||
} | } | ||
| Line 109: | Line 117: | ||
// put your main code here, to run repeatedly: | // put your main code here, to run repeatedly: | ||
| − | // | + | //Configure the first ColorLED to maximum red |
| − | + | strip.setPixelColor(0, 255, 0, 0); | |
| − | // | + | //Set the ColorLED |
| + | strip.show(); | ||
| + | |||
| + | //wait 1 second | ||
delay(1000); | delay(1000); | ||
| − | |||
| − | |||
| − | // | + | //Configure the first ColorLED to maximum green |
| + | strip.setPixelColor(0, 0, 255, 0); | ||
| + | //Set the ColorLED | ||
| + | strip.show(); | ||
| + | |||
| + | //wait 1 second | ||
delay(1000); | delay(1000); | ||
| − | // | + | //Configure the first ColorLED to maximum blue |
| − | + | strip.setPixelColor(0, 0, 0, 255); | |
| + | //Set the ColorLED | ||
| + | strip.show(); | ||
| − | // | + | //wait 1 second |
| − | delay( | + | delay(1000); |
} | } | ||
</syntaxhighlight> | </syntaxhighlight> | ||
Latest revision as of 20:06, 1 December 2017
| Language: | English • 中文 |
|---|
|
The product number of Sensor-Color LED is: MSDL11 Sensor-Color LED is full color LED, adopting single serial cascade protocol. Only one I/O port can control the RGB color of each LED on the line. If the power supply supports, it can support the cascade of as many as 1024 LEDs.
ContentsIntroduction of Sensor Pin
Features
Specification
Documents
UsageBasic FunctionalityThe ColorLED is a trinket which emits different colors based on the set red, green, and blue values. A Core module can control the ColorLED to output the desired colors. Note: ColorLEDs can be connected together in a daisy chain fashion, and each ColorLED can be addressed individually using the index number. First ColorLED being 0, second ColorLED being 1, etc. ProgrammingIntroductionThe ColorLED is used as an output pin. The library is based on the Adafruit_NeoPixel library (Read more) is used to control the ColorLED. Most of the functions are similar. Key Functions
ExampleThis is a simple example which:
Note: Important lines of code are highlighted. //Include the required libraries to control the ColorLED
//Based on: https://learn.adafruit.com/adafruit-neopixel-uberguide/arduino-library
#include <Microduino_ColorLED.h>
//Define the pin the ColorLED is connected to
const int COLORLED_PIN = 6;
//Define the number of ColorLEDs daisy chained together
const int COLORLED_NUM = 1;
//Declare and initialize the ColorLED object
ColorLED strip = ColorLED(COLORLED_NUM, COLORLED_PIN);
void setup() {
// put your setup code here, to run once:
//Initial serial communication port at 9600 baud
Serial.begin(9600);
//Initialize the ColorLED class object
strip.begin();
//Initialize all ColorLEDs to 'off'
strip.show();
}
void loop() {
// put your main code here, to run repeatedly:
//Configure the first ColorLED to maximum red
strip.setPixelColor(0, 255, 0, 0);
//Set the ColorLED
strip.show();
//wait 1 second
delay(1000);
//Configure the first ColorLED to maximum green
strip.setPixelColor(0, 0, 255, 0);
//Set the ColorLED
strip.show();
//wait 1 second
delay(1000);
//Configure the first ColorLED to maximum blue
strip.setPixelColor(0, 0, 0, 255);
//Set the ColorLED
strip.show();
//wait 1 second
delay(1000);
}Copy and paste the code above to the Arduino IDE or Download the above example: n/a Program Download
Programming
Hardware Setup
Results
Application
ProjectHistoryGallery
|
