Sensor-Color LED

Language:	English  • 中文

Microduino-Color led The product number of Sensor-Color LED is: MSDL11 Sensor-Color LED is full color LED, adopting single serial cascade protocol. Only one I/O port can control the RGB color of each LED on the line. If the power supply supports, it can support the cascade of as many as 1024 LEDs. Introduction of Sensor Pin Pins of the sensor: PIN1: GND PIN2: VCC General signal pins: PIN3(IO1): digital/analog signal PIN4(IO2): NC(null) Special signal pins: If it is IIC: IO1/IO2 are respectively SDA/SCL. If it is soft serial port: IO1/IO2 are respectively tx/rx. Special to Sensor-Color LED sensor pins PIN1: GND PIN2: VCC PIN3(IO1): Digital signal output PIN4(IO2): NC Microduino sensor can communicate with core module through the connection with Microduino-Module Sensor Hub. Color LED General Pin Out Sensor / Trinket's Pin Out PIN1 (GND) GND PIN2 (VCC) VCC PIN3 (SIGNAL-A) Digital Output (One-wire communication) PIN4 (SIGNAL-B) Not Connected General Pin Out is the standard pin out of a Sensor / Trinket connector. Sensor / Trinket's Pin Out is this specific Sensor / Trinket's wiring in relation to the General Pin Out. SIGNAL-A / SIGNAL-B are signals that could be digital input, digital output, analog input or analog output. Or special signals such as serial communication (SoftwareSerial, IIC (I2C), etc) or other special signals. Not Connected refers to the Pin not being used for this particular Sensor / Trinket. Read more about the hub module. Features With small size which is easy to install; Adopts single serial cascade protocol, which makes it cascadable; Only one I/O port can control the RGB color of each LED on the line; Can achieve 256-grade (1600W) toning of RGB, and the scanning frequency is not less then 400Hz/s Specification Sensor voltage 5V working voltage Size of the sensor Size of the board: 23.5mm*13mm 1.27mm-spacing 4Pin interface connected with sensorhub CAD drawing of the sensor: File:Sensor CAD.zip Function description Adopts WS2812 lampwick Adopts single serial cascade protocol, which makes it cascadable Only one I/O port can control the RGB color of each LED on the line Can achieve 256-grade (1600W) toning or RGB, and the scanning frequency is not less then 400Hz/s When the updating speed is 30 frame/s, the cascading number is no less than 1024 Connection This sensor can be connected to the following interfaces of the core: D2~D13,A0~A7 Multiple sensors cascade: Connect the (OUT) of the former Sensor-Color LED to the (IN) of the latter Sensor-Color LED. Documents Schematic diagram: File:Sensor-Color LED.Zip Main chip: File:WS2812 datasheet.pdf You can use the sample programs in the following IDE libraries to do experiment on your own: _07_Sensor_LED_WS2812 Development Program Download Download and unzip the program File:Sensor-Color-LED.zip Programming Follow the Software Getting Started Guide. Select the Board, Processor and Port. Click [File]->[Open], browse to the project program address, and click "Microduino_Sensor-Color_LED_Test.ino" to open the program. After confirming all these items are correct, click "→" to download the program to the development board. Hardware Setup Referring to the following diagram, connect the Sensor-Color LED to the digital port D6 of Microduino-Sensorhub. Results After download, observe the LED strip.. LED flashes in red and green successively with the interval of 1s. Application LED full color light source Project Birthday Lamp Bluetooth Lamp Rhythm Lamp Applause Enthusiasm Detection Colored LED History Gallery File:MicroduinoColorLED-F.JPG mCookie-Color_LED-Front File:Microduino-ColorLED-b.JPG mCookie-Color_LED-Back