Open Source WiFi Weather Station

From Microduino Wiki
Revision as of 23:07, 18 December 2018 by Sonny (talk | contribs) (→‎Program Download)
Jump to: navigation, search

Outline

  • Project: Open Source WIFI Weather Station System.(ESP8266 connected to Blynk)
  • Objective: To get temperature, humidity, light intensity and PM2.5 at the weather station.
    • Note: PM2.5 refers to atmospheric particulate matter (PM) that have a diameter of less than 2.5 micrometers
  • Difficulty: Medium
  • Time-consuming: 2-Hour
  • Maker: Ray

Introduction:

  • Read temperature, humidity, light intensity and PM2.5 data and display those data on the screen.
  • Upload the data to Blynk.
  • View data on phone anywhere using the Blynk app.
  • Created by Microduino with Microduino components.

Bill of Material

Microduino Equipment

Note: Different revisions may contain different components.
Module Number Function
Microduino-Core+ 1 Core board (Arduino)
Microduino-USBTTL -OR- Microduino-USBTLL-C 1 Programmer for Core board
Microduino-WIFI(ESP) 1 WiFi communication module
Microduino-Sensorhub 1 Connector Hub to connect sensors
Microduino-Duo-h -OR- Microduino-Cube-S1 1 Extension board
Microduino-OLED 1 Display
Sensor Number Function
Microduino-Temp&Hum -OR- Sensor-Tem&Hum-S2 1 Digital temperature and humidity sensor
Microduino-Air Quality 1 Air quality detector
Microduino-Light 1 Light-sensitive sensor
GP2Y1010AU0F 1 PM2.5 sensor

Other Equipment

Equipment Number Function
Micro-USB cable 1 For program download and power supply
GP2Y1010AU0F 1 PM2.5 sensor
Screw 7 Fixate modules
Screwdriver 1 Fixate screws
Shell 1
WeatherStationMatiralAll.png
Note: Different revisions will contain different components.

Most noteable are:

  • Duo-V will be replaced with a Microduino-Cube-S1.
  • Humidity/TempSensor will be replaced with a Tem&Hum-S2.

Principle of the Experiment

This Weather Station can detect data including:


Other functions:

Get and Configure Blynk

Next, we'll learn how Microduino interacts with Blynk through the configuration process of the Weather Station.

Get Blynk Phone Client

Add Configuration Items

    • You can scan the two-dimension code below to get Weather Station APP.
BlynkWeatherStationLink.png


  • Also, you can make your own one.
  • In this case, you can click the panel and call out WIDGET BOX, on which you can see many choices.
BlynkSetting3.png


  • Add Value Display item and name "temperature" to display Temperature value acquired.
  • Select V2 on INPUT; Choose PUSH on READING FREQUENCY, which indicates the temperature is sent from the Weather Station and the frequency is controlled by Microduino Client.
BlynkSetting4.png


The corresponding code at the Microduino Client is: 

void senTempHumi() {
  am2321.read();
  float sensor_tem = am2321.temperature / 10.0;
  float sensor_hum = am2321.humidity / 10.0;
  Blynk.virtualWrite(V2, sensor_tem);
  Blynk.virtualWrite(V3, sensor_hum);

  oled(sensor_tem, sensor_hum, sensor_light, sensorPM25, Sensor_etoh); 
}


  • The setting of the humidity is similar with that of temperature; Set INPUT as V3 and send it through a timer function " senTempHumi()".
BlynkSetting5.png


  • The frequency of the timer can be achieved by codes below: 
void senTempHumi() {
  SimpleTimer temHumtimer;
  temHumtimer.setInterval(2000L, senTempHumi);
}


  • Set PM2.5's INPUT as V6, READING FREQUENCY as 5s, which represents frequency of the acquired PM2.5 data.
BlynkSetting6.png



  • The corresponding code at the Microduino Client is: 
BLYNK_READ(V6) {
  Blynk.virtualWrite(V6, sensorPM25);
}


  • Similarly, set the INPUT of the Light Sensor as V4 and the frequency is to get value every 3s.
BlynkSetting7.png



  • The corresponding code at the Microduino Client is: 
BLYNK_READ(V4) {
  sensor_light = map(analogRead(A0), 0, 1023, 0, 255);
  Blynk.virtualWrite(V4, sensor_light);
}



  • The INPUT of the methane gas is V5 and the frequency is to get value every 5s.
BlynkSetting8.png



  • The corresponding code at the Microduino Client is: 
BLYNK_READ(V5) {
  Sensor_etoh= map(analogRead(A2), 0, 1023, 0, 30);
  Blynk.virtualWrite(V5, Sensor_etoh);
}



  • Finally, your phone panel turns into this:
BlynkSetting12.png

Programming

  • Stack Microduino-Core+ and Microduino-USBTTL together.
    • Connect Microduino-USBTTL for program uploading with a USB cable.
    • Attention: Please upload programs before stacking all modules together.
  • Open Arduino IDE for Microduino development environment. (Please refer to: AVR Core：Getting started)
  • Click 【Tool】, make sure the right board card(Microduino-Core+) and processor(Atmega644pa@16M,5V), select the corresponding port (COMX) .
  • Click【File】->【Open】, scan to the program address, click “ESP8266BlynkWeatherStation.ino” and open it.
  • After that, please click the button "→" to upload programs to the development board.

Hardware Buildup

Waetherstep1.jpg
  • Step2
    • Assemble Structure-B1~B5 with Structure-B6.
Waetherstep2.jpg
Waetherstep3.jpg
Waetherstep4.jpg
Waetherstep5.jpg
  • Step6
    • Complete the steps above, then fixate with Structure-B0 and plug in a USB cable. Congratulations! You just finished the buildup of the Weather Station.
  • Step7
    • You can see sensor data on Microduino-OLED after setting.
    • At the same time, you can also see uploaded data of the Weather Station on your phone Blynk.
BlynkSetting13.png

Notes

  • Please make sure the verification code is configured right.
  • Make sure your router runs normally, the SSID and password are correct.
Retrieved from "https://wiki.microduinoinc.com/index.php?title=Open_Source_WiFi_Weather_Station&oldid=23476"