Microduino Altitude Lamp

Outline Project: Microduino somatosensory lamp Purpose: You can use Microduino-10DOF altitude sensor to have somatosensory control of a lamp. Difficulty: High Time-consuming: 4-Hour Maker: Microduino Studio-YLB Principle Here we adopt Microduino-nRF24 wireless communication. Microduino-10DOF first acquires altitude data and get it quantified to color value (0-255), and then send it to the lamp, which gets the value and lightens the lamp. The lamp adopts single-wire-bus WS2812 colored-light with built-in IC chip in each light, which can be freely controlled. Bill of Material Microduino Equipment Module Number Function Microduino-Core 2 Core board Microduino-USBTTL 1 Program download Microduino-nRF24 2 Wireless communication Microduino-BM 2 Battery management Microduino-Colored LED 1 Colored led Other Equipment USB cable 1 For connection Li-on battery 2 Power supply Goblet 1 Frame of the lamp Lamp cover 1 Document Program download: mpu_ws2812 3D module download: File:3D-Ball.zip Make a Lamp Step 1: Prepare a goblet and a lamp cover, and set up the framework. Step 2: Build hardware circuit Equipment needed: Module Number Function Microduino-Core 1 Core board Microduino-USBTTL 1 Program download Microduino-nRF24 1 Wireless communication Microduino-BM 2 Battery management Microduino-Lamp 1 Colored light Battery 1 Power supply Stack all the modules together. Step 3: Program test You will need _99_LCD_NeoPixel, which can refer to: Install Arduino IDE Microduino library support package. After the installation, just open "strandtest" program in the "Examples". Program description: #define PIN 6 Adafruit_NeoPixel strip = Adafruit_NeoPixel(60, PIN, NEO_GRB + NEO_KHZ800); PIN defines the control pin of single wire bus light and "60" defines the quantity of the light. (Users can change that according to personal needs.) After the download, we can the fancy effect of the experiment. Somatosensory Remote-Control Buildup Here we adopt a 3D-printed ball-shaped exterior. Step 1: Build hardware circuit. Equipment needed: Module Number Function Microduino-Core 1 Core board Microduino-nRF24 1 Wireless communication Microduino-BM 2 Battery management Microduino-10DOF 1 Altitude detection Battery 1 Power supply Stack all the modules together freely. Step 2: Build 3D module. Adopt SketchUp to build 3D model according to hardware circuit buildup specification. Step 3: Adopt 3D printer to make the model and make sure the size is right. Overall Debugging Step 1: Program download Decompress program and open two programs respectively—one for sending and the other for receiving. Program Description: Sending end: "mpu.h" is for subprogram of altitude detection. Microduino-10DOF acquires altitude data and then it is quantified to color value (0-225). //=The three lines below are angles between the three axis and the horizontal coordinate system, calculated by acceleration. Angel_accX=atan(Ax/sqrt(Az*Az+Ay*Ay))*180/3.14; Angel_accY=atan(Ay/sqrt(Ax*Ax+Az*Az))*180/3.14; Angel_accZ=atan(Az/sqrt(Ax*Ax+Ay*Ay))*180/3.14; Angel_accX_send=map(abs(Angel_accX),0,90,0,255); Angel_accY_send=map(abs(Angel_accY),0,90,0,255); Angel_accZ_send=map(abs(Angel_accZ),0,90,0,255); Receiving end: Lighten the colored lights after receiving the data. Angel_accX=rec.rf_x; //Receive time sequence and sign values Angel_accY=rec.rf_y; Angel_accZ=rec.rf_z; Serial.print(Angel_accX); Serial.print(","); Serial.print(Angel_accY); Serial.print(","); Serial.print(Angel_accZ); Serial.println(""); colorWipe(strip.Color(Angel_accX, Angel_accY, Angel_accZ), 10); Not receiving NRF data for two seconds, the colored light will be turned off. if(safe_ms>millis()) safe_ms=millis(); if(millis()-safe_ms>2000) { colorWipe(strip.Color(0, 0, 0), 50); } Download to the corresponding hardware. Connect battery to the BM module, turn on the power switch on BM. Or you can adopt USB cable for power supply. Note: If cannot initiate the power after changing battery on BM, you need a USB cable to start that and move the ball to see lamp change. Notice The sending and the receiving ends share one USBTTL, which is for program download. If cannot initiate the power after changing battery, you need a USB cable to start BM.